Mine has an AD suffix, about 2.5k rounds, no failures.
I just purchased mine last week from a Guns2Ammo reddit deal, with a AF date code.
I see the clear decal mentioned, and haven't attempted to peel it to see how the battery terminal is secured. I'll try baking it and see what happens to the decal, probably loosen the adhesive. The deltapoint pro spec sheet says:
• Operating Temperature Range: -20°F to +120°F (-29°C to +49°C)
• Storage Temperature Range: -40˚F to +160˚F (-40˚C to +71˚C)
I assume competitive shooters can get their slides hot enough to boil water? I can do heat related testing, but don't have easy access to a vibration tester. Someone with a paint shaker could do that though, but I don't think it's a vibration issue.
https://www.leupold.com/leupold-core...peManufactured
AB 2015
AC 2016
AD 2017
AE 2018
AF 2019
I see that the o-shaped clear decal is still centered on the + shaped negative battery terminal, but the o-shaped clear decal is no longer centered around the gold/copper circle. Was the clear decal adhesive still working? Could you push it around for this specific failure?
Zooming in on both images it looks like the clear decal has stayed in place and looks undamaged, but the + negative battery terminal has started slipping rearward. The top image of this quote shows that the + punctured through it. All the images you've posted of the + failing shows it moving rearward, caused by movement of the slide.
From the general electronics testing that I've seen, manufacturers may test hot/cold like the operating temperatures found in their manual, and/or vibration. I've yet to see thermal testing and vibration testing at the same time, usually it is one after the other.
I have had poor reliability with a number of AF units, but that should be corrected quickly. The decal is what is keeping the “+” located, so watch it closely and look for shifting of the +.
Likes pretty much everything in every caliber.
Took some measurements with my unit. Again it's new from last week, never fired. Hooked it up to a DC Power Supply and measured the current draw. The battery that came with my deltapoint pro is a Panasonic and measured 3.011V at the time of testing (used it in the deltapoint for a week and left it on my nightstand), so I set the power supply to 3.011V as well.
Minimum brightness .13mA
Maximum brightness .48mA
Below is the always on, as in no 5 minute inactivity shutoff, calculated battery life based on the manufactuer's mAh rating using this calculator: https://oregonembedded.com/batterycalc.htm
Panasonic 225mAh https://b2b-api.panasonic.eu/file_st...leversion/3627
Minimum brightness 61.3 days
Maximum brightness 16.6 days
Energizer 235 mAh http://data.energizer.com/pdfs/cr2032.pdf
Minimum brightness 64.02 days
Maximum brightness 17.34 days
The spec sheets of both Panasonic and Energizer say the cutoff (dead) voltage is 2.0V for the battery. Using a DC power supply I was able to get the voltage down to 1.744V before the laser was getting too dim for me to see, but I didn't pay attention to what the current was at that time. That means as long as the battery is able to supply any bit of power, the unit will turn on.
I'm not sure how accurate Oregon Embedded's calculator is, but it seems to line up with the 2+ weeks being seen for active users.
The clear decal covering the + shaped negative battery terminal does not glow under UV light, so there's no easier way of seeing it. I put the deltapoint pro, upside down and slanted so that any adhesive failure would cause the + to drop or move towards the back, in an oven at +50C without a battery inside. After about an hour I took it out and didn't notice anything weird. Ran it up to +70C for less than 2 hours, and then -40C for less than 2 hours. The clear decal and + shaped negative battery terminal is still in place. The temperatures used are what Leupold calls out on their spec sheet, but I'm pretty sure a pistol slide gets much hotter. I'm not sure if this electronics oven can go past 100C as we never test anything that high, and I don't have a discarded food oven. Anyone with a hot plate for casting or a toaster oven for cerakote can try that on theirs.
I am well over 7,000 rounds on the ruggedized prototype and it is running strong. I am reasonably confident that Leupold has the fixes down. There are two more test units on the way to me.
Likes pretty much everything in every caliber.