AIWB (Appendix Carry)

[Chefdog]

FYI, I use hard plastic spacers to bump out the DCC clip to avoid that "out and in and back out at the wing" shape of the belt and have a smooth beltline profile

I too am wearing dark blue jeans, black and white vans, and a dark tee shirt haha

Do you have a wedge on that holster? It's tucking pretty well already

Thanks for the tip, I’ll see what I can find for a spacer.
That’s the dad uniform, isn’t it?
No wedge, but I’ll probably try the heel cushion hack or see if my wife has any of those yoga blocks around somewhere to cut up.

[Noah]

Thanks for the tip, I’ll see what I can find for a spacer.
That’s the dad uniform, isn’t it?
No wedge, but I’ll probably try the heel cushion hack or see if my wife has any of those yoga blocks around somewhere to cut up.

https://www.amazon.com/gp/aw/d/B07TR...b_b_asin_title

[Chefdog]

https://www.amazon.com/gp/aw/d/B07TR...b_b_asin_title

Nice 🤙

[Elwin]

Thanks for the tip, I’ll see what I can find for a spacer.
That’s the dad uniform, isn’t it?
No wedge, but I’ll probably try the heel cushion hack or see if my wife has any of those yoga blocks around somewhere to cut up.

A yoga block and Velcro tape are up there with loctite and paint markers as contenders for most important things on my workbench.

[CSW]

Try this:
https://www.mastermindtactics.com/shop/acp-fixed

Game changer.
The Dr. Scholl's hack, meh.

Even the triangular foam, or flat foam wedges are better than the insole .

[Dark Star Gear]

Thanks for the tip, I’ll see what I can find for a spacer.
That’s the dad uniform, isn’t it?
No wedge, but I’ll probably try the heel cushion hack or see if my wife has any of those yoga blocks around somewhere to cut up.

If you haven't found something, lemme know (email), I can set you up with some longer screws and posts as well, to do just that. I've not listed the kit yet, but will soon.

[03RN]

Plenty of people run holsters that way! I prefer the single DCC clip over the trigger guard, because with 1 clip on the middle of the holster, it's closer to the peak of my stomach, and, since the leverage point farther away from the trigger guard, it is easier for a bit of rotation to sink the grip too close to the belt line, unless you carry the gun a little higher over the belt.

With the 1 clip right over the trigger guard, the small amount of rotation you do get will not significantly affect your amount of access to the frontstrap and bottom of the trigger guard for your draw.

Personally I don't like the change of angles when drawing when using one clip.

[Chefdog]

Try this:
https://www.mastermindtactics.com/shop/acp-fixed

Game changer.
The Dr. Scholl's hack, meh.

Even the triangular foam, or flat foam wedges are better than the insole .

🤙

If you haven't found something, lemme know (email), I can set you up with some longer screws and posts as well, to do just that. I've not listed the kit yet, but will soon.

Thank you. I used the washers off of the monoblock clip under the DCC clip and they did the job. I don’t plan on carry this gun much, if at all, other than for some range time so it’s not a big deal, but I’ll keep it in mind for the future.

[spiro]

Just wanted to show off a few of my appendix rigs. I run an MR920 with a Holosun 507c and a Dan Wesson Valor in .45

Top holster is from Legacy Firearms Co. It uses a monoblock clip. This holster doesn't have a claw but still conceals well.

The JMCK Wing Claw 2.5 is one of my favorite holsters. I did switch the wing for something more tapered. I ordered the wing from C@G Holsters. I also added a tear shaped wedge on the back. I use the Constantine edc belt when I carry a full size steel frame gun. It's extremely comfortable and makes carrying a heavy gun a breeze.

JMCK Wing Claw 2.5

[spiro]

One more setup. A commander 9mm in LAS Concealment rig.