That's how it should look
While both the OP and I agree that those aren't good extreme spreads, those velocities don't qualify as "anemic". The power factor for his load is 173.4; the PF for a recent lot of Federal AE hardball was 172.5 from my 4" M22-4.
A couple of additional thoughts...are those bullets coated or uncoated? My .45 ACP autoloader handloads use a coated 230-grain RNL bullet and work fine in my bottomfeeders (1911s and M&P45s) but I can't make it through a cylinderful in the revolver without the last round disassembling itself. Those loads are taper crimped to (IIRC) .471". Uncoated bullets worked okay in the past, but coated bullets are apparently too slick. Having bullet length change would definitely mess up the ES. (My solution to this issue was to get some coated 225-grain coated RNFPs and crimp them in the crimp groove using the same Redding profile crimp die as the OP.)
If the bullets were seated to the crimp groove and then taper crimped, the case mouth and the case immediately below it would just be holding onto air rather than bullet. Seating them deeper as in @03RN's picture and using the same taper crimp would give the case mouth something to hang onto. It would also raise the pressure somewhat, though within safe levels. My Speer #3 manual shows loads from 6-8 grains of Unique under a 255-grain LSWC in a 1955 Target (now the M25-2). My old Lyman Cast Bullet Manual shows 4.5 grains of Bullseye under a 238-grain #452423 LSWC. Sierra's 5th Edition shows a max load of 5.4 grains of Bullseye under their 240-grain JHC in .45 AR brass. So there's a bit of leeway going up in pressure.
I agree on most points, but velocity in the 600s seems pretty wimpy to most of us that think in terms of field use and the commonly loaded velocities of this type bullet. The sedate old school 185 gr target swc loads are in the 700s fps range and generally considered pretty soft. Power factor isnt a measure most field shooters think of in comparing loads. Trajectory at that level would be fairly loopy if one wanted to reach out very far.
My loads with the 452424 bullets looked similar to 03RNs, a small amount of bullet shoulder exposed ahead of the case mouth. I seated them bit by bit until they cleared the magazine easily then a tiny bit more, and called it good. The OAL numbers meant little so long as they functioned in the magazine. There were no OAL figures to work with for those bullets that I knew of at the time, but they worked fine.
...and this all reminds me of how simple most revolver loading is. Seat to crimp groove, moderate to heavy roll crimp, drive on....
“Far better it is to dare mighty things, to win glorious triumphs, even though checkered by failure, than to take rank with those poor spirits who neither enjoy much nor suffer much, because they live in the gray twilight that knows neither victory nor defeat.”
― Theodore Roosevelt
I had to look in my old chrono records from 1988.
A bowling pin shooter made some bullets that were a H&G 68 nose with a longer body. They weighed 240 grains and I loaded 5.4 of 231 for an average velocity of 823 in my 5" 1911. 6 shots chronoed 813 low and 831 high.
Yeah, the trajectory would be pretty loopy…and a lot of the shooters here might fit that description too.
At this point I'd suggest ditching the Redding die. I really don't like them for cast bullets anyway because they can swage the bullet diameter down a bit, sort of like a LEE Factory Crimp Die, which I avoid as well. Consider using a taper crimp to preserve the relationship between the case mouth, and the end of the cylinders chamber. Do you have any pics you can post of the bullet design? Before I suggest juggling the seating depth it would be handy to see it. Also, Bullseye is a wonderful powder for 45 ACP, but I lean more towards slower burning powders as well. I'd suggest only making one change at a time and see how your groups are affected by each change. I used to load 255 gr Lyman 452190, a flat, round nose design for pins but ended up not sticking with it because of the recoil involved. I was using a book max. load of Unique to get more power, and (hopefully) soften the recoil impulse a bit. It was a heavy load, and as I've already mentioned, I ended up going back to 230 gr, and bought an LBT mould specifically for pins.
Malo periculosam, libertatem quam quietam servitutem
I prefer the tumult of liberty to the quiet of servitude
-Thomas Jefferson
I prefer dangerous freedom over peaceful slavery.
Strange, I went to Bullseye for .45 Minor - 200 gr coated + 3.5 gr Bull = 660 fps or so.
A lot of "so", my variation is greater than I like but less than yours and less than with other powders.
Code Name: JET STREAM