Received it today and installed. Will try it out and compare to the ported SAS slide and the True barrel with the mini comp.
Barrel length is shorter than the True threaded barrel.
With the comp it’s shorter than a P365XL.
I don’t quite know what use it’ll have for me. I guess it’ll depend on how it shoots. My impression is that slowing the slide on the SAS with ports makes it a fair amount softer shooting.
What was the cost for the comp and barrel?
www.hero911.org
Hero911 when seconds save lives.
I'm really looking forward to the 43X version. If it works half as well as the JTTC I have on me G45 I'll be really happy.
Had a fun range trip with the P365X/Boresight/407K/PMM Gen 2 Comp today. I compared it to the P365XL with a 507K on it.
With the 365XL I don't find the recoil objectionable but I'd be lying if I said I didn't lose the dot in recoil sometimes.
Switched to the P365X with the PMM comp. Wow. The recoil felt like shooting a Glock 42 .380 if I remember that gun correctly. Very easy to keep the dot in the 407K window without really trying. Also very accurate. I was shooting Federal AE9FP 147gr and I did have a couple occasions of the slide not locking back on the last shot of a 10-round XL mag. 147gr HST had a little more pop and no problems locking the slide back.
Top target is my group at 15Y as I sighted in the 407K (lowering POI -- not vertical stringing.)
I'm now newly concerned about the shorter barrel velocity and expansion of the load I've got lots of ... 147gr HST. Never really worried about it with the XL length.
This is my second PMM comp. The first is the JTTC Ultra which I have on a G45... also amazing once I found the right recoil spring weight (15lbs in my case).
@vandal
I have almost the same setup and had to use it instead of my competition gun for some drills.
It was impressive that I could use it pretty decently for that.
I presume we expect this not to run with softer ammo? I got mine yesterday and shot it today. Three FTEject in 15 rounds of weakest ammo I have, which is 115 gr PMC. I took a few rounds of 150 gr Syntech with me and they were fine, as were 124 gr Norma and 147 gr Ranger. I liked it with 124 gr Norma the best.
Doesn't read posts longer than two paragraphs.
I posted recoil spring options for weaker ammo plus comps earlierOriginally Posted by YVK
ISMI spring with 1-3 coils removed.
I’ll also test the P365-380 RSA spring in the 9mm comp version if the length and size is the same.
Is it really worth the hassle to run 147 and greater weights ? The 115-124gr and +P seem to make the most difference and improvement.
I ran about 400 rounds through my PMM P365X the other day w/ Blazer 115 gr, Federal 115 gr, Norma 124 gr, Norma 124 gr Envy PCC, and Hornady 135 gr Critical Duty. I had no issues which actually surprised me as they tend to like hotter 124 vs weaker 115. I haven’t had issues with my other PMM comps except my P320 Ultra JTTC two port. I had to install the DPM recoil spring in order to get it to run even with the Norma Envy which is supposedly 1345fps, I haven’t had any issues since installing the DPM system even with light ammo. They are amazing with hot ammo and seem to recoil even less than weaker ammo as the comp has more gas to really work. Picture is 25 yards with Blazer 115 gr.
Seriously considering one of these to try out, not sure how much of a difference will make for me as I almost exclusively shoot 147gr ammo.
Reply With Quote