Page 17 of 20 FirstFirst ... 71516171819 ... LastLast
Results 161 to 170 of 196

Thread: JCN’s Taurus 380 Snubbie review

  1. #161
    The Nostomaniac 03RN's Avatar
    Join Date
    Aug 2017
    Location
    New Hampshire
    One reason I look at the gun is to insure there isnt a case left in the cylinder or under the ejecter.

    Much less, if not non existent, of a problem with moon clips.

  2. #162
    Site Supporter
    Join Date
    May 2012
    Location
    South Louisiana
    Quote Originally Posted by revchuck38 View Post
    @revolvergeek - The 22-4 was specifically designed to be shot only with moon clips or .45 AR brass. Mine works fine.
    Clearly so. Wish I had been aware of that when I bought it. It was a very different revolver from the old 25-2 1955 Target models (not just for the sights). My problem with the one I had wasn’t just that it was different, but that it was inconsistent. Four of the chambers would generally work with .45 acp without moon clips, the other two just let the rounds drive deeper into the chamber with hammer strikes. If none of them worked it would not have annoyed me as much.


    .45 AR is a fun cartridge and easy to reload. I have a few boxes loaded with the old Speer 200 jhp Flying Ashtray bullet. I also have some of Matt’s 260 hbwc Bullets that I planed to load backwards to make something like the old
    British man stopper load to shoot in my old Webley.
    Last edited by revolvergeek; 05-25-2021 at 08:09 PM.

  3. #163
    Member
    Join Date
    Jun 2019
    Location
    out of here

    Two more months

    Have been using it intermittently as a weak hand trigger trainer and I like the gun very much. The trigger has smoothed out nicely and with the spring kit, it’s quite an enjoyable gun.

    I would have no problem carrying this over a 38 J frame.

  4. #164
    Member
    Join Date
    Jun 2019
    Location
    out of here

    Light strikes

    Light strikes with dirty chambers.



    Ammo likely partially to blame. I’m not going to clean it and will see if still light strikes.

    But I think it’s at least partially the dirty chambers because the moon wouldn’t seat properly and caused binding so I know it wasn’t flush.

    Gun likes to be clean for sure. Just testing for failure patterns.

  5. #165
    Member
    Join Date
    Jun 2019
    Location
    out of here

    Follow up

    So I had a chance to do some follow up and determined that it wasn’t due to dirty chambers.

    It was bullet shape.

    The way the chambers are cut, the shelf doesn’t give enough clearance to fit the wider bases and they don’t seat.

    Name:  73579252-FE2C-4BB1-8C2D-3E1D78A13B7A.jpg
Views: 217
Size:  53.4 KB

    Name:  504932F5-BD9F-437F-9E92-37F84BB037E5.jpg
Views: 208
Size:  24.6 KB

  6. #166
    Member
    Join Date
    Jun 2019
    Location
    out of here

    Dremel

    Clearanced a little and now will take all different bullet shapes.

    Name:  49CC767B-076D-4A09-AD3E-C66E07F47022.jpg
Views: 228
Size:  22.3 KB

    I can polish it later if I care to.

  7. #167
    Member
    Join Date
    Jun 2019
    Location
    out of here

    Light strikes

    So I have a lot of dry fire rounds through the revolver and brought it to the “intro class” thing that I taught for women.

    It was a hit. But there were a few light strikes for the women with looser grips.

    So I figure the springs are a little light for reliable use.

    When I tested it:

    Name:  1A7545C5-4CFB-4447-95F5-F9EC3A193411.jpg
Views: 178
Size:  53.0 KB

    With use it had come down to low 8 pound range.

    The action is very smooth now though.

    So I was prepared to do some fancy spring swaps.

    But instead I tested the washer shim approach I used on my 22LR Shadow 2.

    Name:  0478425F-CF36-4A32-BF5A-4B99030671F6.jpg
Views: 177
Size:  53.0 KB

    With one small washer put on the lower side and confirmed no binding, the pull weight gives more margin. Should be enough to fire most things.

    See @Clusterfrack what seems like a PIA to some is just another learning opportunity that can be internalized and applied to reduce frustration in other scenarios.

  8. #168
    Revolvers Revolvers 1911s Stephanie B's Avatar
    Join Date
    Mar 2014
    Location
    East 860 by South 413

    Re: Dremeled

    Quote Originally Posted by JCN View Post
    Clearanced a little and now will take all different bullet shapes.

    Name:  49CC767B-076D-4A09-AD3E-C66E07F47022.jpg
Views: 228
Size:  22.3 KB

    I can polish it later if I care to.
    The good thing is that if you screwed it up, you've wrecked a Taurus. No big loss.

  9. #169
    Member
    Join Date
    Jun 2019
    Location
    out of here
    Quote Originally Posted by Stephanie B View Post
    The good thing is that if you screwed it up, you've wrecked a Taurus. No big loss.
    And I bought it used for a steal too!


  10. #170
    Member
    Join Date
    Feb 2013
    Location
    ATL
    Fantastic thread JCN! Quick question regarding recoil, what would you compare the .380 to a 148 wadcutter or less, .32 Long or .32 mag. Appreciate your insight.

    Dave

User Tag List

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •