Reloading 9mm for a semi auto

[TRSmith]

Hello!
I am new to your forum, new to shooting, and new to reloading. I have started with the basic Lee Loader kit for my 38 snubby, and I am getting interested in reloading for my 9mm Taurus. I realize that reloading for the revolver is pretty straight forward, but I know using reloads in a semi auto will be more touchy. How tricky might this be? My 9mm goal is to load some casted bullets over a light powder charge for some low-recoil self-defense practice at 30 feet. I have some Titegroup powder, some Accurate #2 powder, a caliper, and my eyes on a LEE C press. Please advise...

[SecondsCount]

Welcome!

What is the weight in grains of the bullet that you plan on shooting?

I have tried 115 grain cast bullets in 9mm and was having barrel leading problems by the time I loaded up enough powder to get the slide to operate. 147 grain bullets worked well, and I am currently loading 135 grain powder coated bullets with Clay Dot which is a fast burning powder similar to what you are using.

[JM Campbell]

Hello!
I am new to your forum, new to shooting, and new to reloading. I have started with the basic Lee Loader kit for my 38 snubby, and I am getting interested in reloading for my 9mm Taurus. I realize that reloading for the revolver is pretty straight forward, but I know using reloads in a semi auto will be more touchy. How tricky might this be? My 9mm goal is to load some casted bullets over a light powder charge for some low-recoil self-defense practice at 30 feet. I have some Titegroup powder, some Accurate #2 powder, a caliper, and my eyes on a LEE C press. Please advise...

Hi-Tek coated lead projectiles would be a better option then the uncoated lead for a semi. If your set on loading lead projectiles you will need to bell the cases so when seating the projectiles you will not shave the sides of the projectile.

https://forums.brianenos.com/topic/9...-any-examples/

https://youtu.be/f3kTZgfPTD8


Sent from my iPhone using Tapatalk

[JM Campbell]

Another thought is where are you located? A really cool member here with reloading experience might just be local to you and be able to help get you started in person.


Sent from my iPhone using Tapatalk

[TRSmith]

Another thought is where are you located? A really cool member here with reloading experience might just be local to you and be able to help get you started in person.


Sent from my iPhone using Tapatalk

I am in Michigan, Pontiac area.

[olstyn]

Bare lead + Titegroup = lots of smoke, and potential leading problems. As JM Campbell said, you'll be much better off with coated bullets. In terms of being more "touchy" to load, I would say that 9mm is not particularly difficult - it's what I first learned on, and I never had any real issues. Generally speaking, loads from a manual should be in the safe range which will cycle the gun without causing problems, so I'd recommend that you start there. (Coated lead bullets can usually use the same load data as equivalent weight/similar profile bare lead bullets.)

[TRSmith]

Hi-Tek coated lead projectiles would be a better option then the uncoated lead for a semi. If your set on loading lead projectiles you will need to bell the cases so when seating the projectiles you will not shave the sides of the projectile.

https://forums.brianenos.com/topic/9...-any-examples/

https://youtu.be/f3kTZgfPTD8


Sent from my iPhone using Tapatalk

So, lead does not work well with a semi auto? I am not set on a bullet, I am just trying to find the easiest/best way to reload one practice loads.

[TRSmith]

Bare lead + Titegroup = lots of smoke, and potential leading problems. As JM Campbell said, you'll be much better off with coated bullets. In terms of being more "touchy" to load, I would say that 9mm is not particularly difficult - it's what I first learned on, and I never had any real issues. Generally speaking, loads from a manual should be in the safe range which will cycle the gun without causing problems, so I'd recommend that you start there. (Coated lead bullets can usually use the same load data as equivalent weight/similar profile bare lead bullets.)

Thanks for the helpful info.

[Borderland]

Welcome to the forum.

The difference in revolver loads and semi-auto is the crimp. Revolver loads generally take a roll crimp (cannelured bullet) and semi-auto a taper crimp. I would suggest doing your bullet seating and crimping separately. There are some good die sets out there that seat and crimp in the same stroke but the adjustment can be a challenge for a new reloader. The reason I say this is applying a taper crimp is a bit tricky. Too much will crush a bullet and too little will allow the bullet to migrate. I do all of my taper crimping with an adjustable crimp die after I seat the bullet. I use a Lee Factory Crimp die but there are other good crimp dies out there. A good test for proper crimp is to try to push the bullet into the case on a hard surface like your reloading bench. Also use your barrel as a gauge and drop test your ammo. I use a Wilson case gauge but your barrel works. If they won't drop your cases are too fat probably due to a sizing die not adjusted properly or worn out brass.

I also use coated or FMJ bullets to avoid leading. A bullet that is slightly too small for your barrel will cause leading. Once that starts it sucks hugely.

Just more stuff to know about but it isn't that hard.

https://youtu.be/h1LEbcRDs70

[daved20319]

I load for both 9mm and .45 ACP, I use coated lead in the .45's and jacketed in the 9mm, but I'm loading full or nearly full power loads to be similar to my carry/SD ammo. Nothing particularly tricky about loading for pistols, although I don't crimp as such, just enough to iron out the case mouth bell. I also use my gun barrels as case gauges, a bullet profile or seating length that works in one gun may not in another. CZ's are notorious for having short chambers, Glocks are at the other end of the spectrum. Also, some profiles may work in the gun's chamber, but not in the mag, my Sig can be troublesome with certain truncated cone bullets because of the magazines. If you do stay with lead bullets, Lyman makes a series of small reloading booklets that include load data for a small number of similar load types. They have one for popular pistol calibers, and it includes data for lead bullets. Might be worth picking one up. Good luck, and enjoy!

Dave