Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: Which Glock Disassembly tool to get?

  1. #1
    Member
    Join Date
    Aug 2011
    Location
    SATX

    Which Glock Disassembly tool to get?

    I am going to start learning to take care of my own G19 so will be needing a disassembly tool. I noticed there seem to be a lot of them out there so I am looking for advice from Glock armorers on which one to get. I don't mind the factory tool if you guys say it is durable and works.

    Thanks

  2. #2
    Member ST911's Avatar
    Join Date
    Dec 2012
    Location
    Midwest, USA
    Last couple of times I detail stripped a Glock I used a Fisher space pen refill, or the nub on a handcuff key.

    I have a bag of the armorer tools, PM your address and I'll send you one.

    Any 3/32 punch otherwise.
    Last edited by ST911; 08-11-2018 at 03:52 PM.
    الدهون القاع الفتيات لك جعل العالم هزاز جولة الذهاب

  3. #3
    I use a 3/32” punch. I don’t remember the make but you can probably get one on Amazon for a couple of dollars. The only differences between the Glock Armorer’s Tool and a generic punch are the plastic handle and a slightly longer shaft.


    Sent from my iPhone using Tapatalk
    –————————————————
    My posts only represent my personal opinion and do not necessarily reflect the opinions or official policies of my employer. Obvious spelling errors are likely the result of an iPhone keyboard.

  4. #4
    Site Supporter
    Join Date
    Feb 2011
    Location
    Albuquerque, NM
    As noted above, while pretty much anything will work, but this NcStar G5+ Glock Pocket Tool is pretty awesome:

    Name:  Screen Shot 2018-08-11 at 4.02.39 PM.jpg
Views: 344
Size:  15.2 KB
    Name:  Screen Shot 2018-08-11 at 4.02.56 PM.jpg
Views: 343
Size:  16.4 KB
    Name:  Screen Shot 2018-08-11 at 4.03.08 PM.jpg
Views: 346
Size:  22.2 KB
    Name:  Screen Shot 2018-08-11 at 4.03.27 PM.jpg
Views: 344
Size:  22.4 KB

    3/32" punch, 3/16" magnetic nut driver/front sight tool, and mag disassembly tool. It also functions as a striker assembly stand and makes assembly/disassembly a little easier.

    I really like mine.

  5. #5
    Member
    Join Date
    Aug 2011
    Location
    SATX
    Quote Originally Posted by Tom_Jones View Post
    As noted above, while pretty much anything will work, but this NcStar G5+ Glock Pocket Tool is pretty awesome:

    Name:  Screen Shot 2018-08-11 at 4.02.39 PM.jpg
Views: 344
Size:  15.2 KB
    Name:  Screen Shot 2018-08-11 at 4.02.56 PM.jpg
Views: 343
Size:  16.4 KB
    Name:  Screen Shot 2018-08-11 at 4.03.08 PM.jpg
Views: 346
Size:  22.2 KB
    Name:  Screen Shot 2018-08-11 at 4.03.27 PM.jpg
Views: 344
Size:  22.4 KB

    3/32" punch, 3/16" magnetic nut driver/front sight tool, and mag disassembly tool. It also functions as a striker assembly stand and makes assembly/disassembly a little easier.

    I really like mine.
    That looks pretty intimidating! Not to insult your gear, but in all seriousness, when I saw NcStar I thought it was the same outfit that made those low-end rifle scopes. But if you say it's good, I'll check it out again.

  6. #6
    Site Supporter
    Join Date
    Feb 2011
    Location
    Albuquerque, NM
    Quote Originally Posted by Redhat View Post
    That looks pretty intimidating! Not to insult your gear, but in all seriousness, when I saw NcStar I thought it was the same outfit that made those low-end rifle scopes. But if you say it's good, I'll check it out again.
    It is the same company that makes shitty airsoft optics. This tool, however, is rad. One of my FB “friends” recommended it. I tried it. I dig it. I’ve got dozens of Glock tools, but this is the one I keep on my bench and use most often. I keep another one in my range bag.

  7. #7
    mama tried blues's Avatar
    Join Date
    Aug 2016
    Location
    blue ridge mtns
    MacGruber to the max!
    “Tactics without strategy is the noise before defeat.” - Sun Tzu | "Everybody has a plan until they get punched in the mouth." - Mike Tyson

  8. #8
    Site Supporter RJ's Avatar
    Join Date
    Jan 2014
    Location
    Tampa FL
    Quote Originally Posted by blues View Post
    MacGruber to the max!
    Seriously.

    I must have one of these!
    Character is doing the right thing when nobody's looking. There are too many people who think that the only thing that's right is to get by, and the only thing that's wrong is to get caught. J. C. Watts
    USPSA#A92555

  9. #9
    Member
    Join Date
    Aug 2011
    Location
    SATX
    "Rad", "MacGruber"...you guys lost me there

  10. #10
    mama tried blues's Avatar
    Join Date
    Aug 2016
    Location
    blue ridge mtns
    “Tactics without strategy is the noise before defeat.” - Sun Tzu | "Everybody has a plan until they get punched in the mouth." - Mike Tyson

User Tag List

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •