This would be my pick
https://shopwilsoncombat.com/1911-Ma...ctinfo/47C-HV/
This would be my pick
https://shopwilsoncombat.com/1911-Ma...ctinfo/47C-HV/
There was another thread started today referencing a Hilton Yam interview. This caused me to look at his 10-8 website. On it he has a section on recommended maintenance/parts replacement.
http://www.10-8performance.com/pages...-in-1911s.html
His recommendations seem pretty aggressive compared to what I've read elsewhere. He probably looks at it from the perspective of a reliable duty 1911 as opposed to a range gun. Of particular note to me was his 5,000 round interval for replacement of the extractor accompanied by the first evidence of erratic ejection.
My question concerns sourcing parts for replacement, since this will now be an every year event. I own a Dan Wesson V-Bob. Can I expect to simply order a Wilson "Bullet Proof" extractor and detent plunger when the time comes or do I need Dan Wesson sourced parts?
Real guns have hammers.
I wouldn't replace your extractor at 5,000rds unless it is damaged or you are starting to get erratic ejection. I have 2 Colts each with over 50,000rds thru them and both are still on their original extractors.
A Wilson Bullet Proof extractor should work fine in your Dan Wesson.
Last edited by Amp; 05-22-2019 at 11:59 AM.
somehow, Mr. Browning fired 6000 rounds and didn't replace anything.....
That statement has more worth ,than a lot of "self taught machinists", would like to believe.
I have gotten more offers to buy my 1911's & Colt Gold Cups , because they ran the competitive courses in centerfire shoots ...without hiccups .
The only real time failure in Competitions & Drills were induced by poor ammo choice. (Mainly my Reloads)
Custer wore the 1st "Arrow shirt".
Given the size & power of “Ivan”, we must now … and ever be Vigilant.
Keep in mind that Hilton's reference point was for a line duty gun, and presumed that there were the resources (parts, time and installation skill-set) on hand within the department. He had presumptively seen sufficient numbers of extractors cause problems at some number above 5K, and established the 5K replacement interval point as the number at which a user could safely enjoy unimpeded success, while at some number north of 5K it could become problematic. Based on his experience and expertise, the 5K number became a good bright line forecasted replacement interval for institutional 1911 use.
I've found his 1911 maintenance milestones to be exceptionally well established and discussed.
Best, Jon
Last edited by JonInWA; 05-22-2019 at 12:25 PM.
My Colt is also going strong but has fewer rounds than yours. Yet I treat it like a lawn mower, something I've read is not recommended for a 1911. But mine isn't a duty gun and when or if it fails it will be at the range during a match or training. Seriously, my Colt is the gun I fuss the least over. I keep my revolvers clean and well oiled [I do oil the 1911], I wipe down and inspect my Beretta M9 after use as I do my AR 15. But the Colt? My last recorded cleaning was Dec. 2017. Oil, good mags and good ammo for me.
I have a lot of respect for Hilton and the fact that he brought to the forefront some very important issues regarding 1911s for duty use (namely that there are better options that work just as well) but I feel like some of his advice is a bit overkill.
If your extractor is losing tension at 5,000 rounds or breaking a hook, then some aspect of your gun is effed up. Probably magazine issues.
To some degree, you need to be your own armorer if you wanna rock a 1911 for carry. That also means you ought to be your own expert opinion on your gun.
For a group of 35 dudes issued 1911s, Hilton's recommendations make perfect sense. Maybe it doesn't for you the individual.
Sent from my moto g(6) using Tapatalk
Thank you WilsonRep. Much appreciated.