Sig P365 - Single Stack 9mm w/10+1 and 12+1

[joshs]

@joshs

MUCH better drop free speed with wheel weights on the 20 round ProMag.

Attachment 83912

If I can get them to run, I’ll give the the least competitive Open rig a shot.

[JCN]

Has anyone tried the Wilson module compared to the Boresight Razorback module?

Yes. Me. I like the Wilson better.

I’ve tried three different- 20-round ProMags and they all are unreliable (not surprising though with their reputation). Did you do anything special to make them work? I use them for range mags and am about to toss them…

What issues are you having? I am comfortable mag tuning in general. I have experience with tuning different mags.

If I can get them to run, I’ll give the the least competitive Open rig a shot.

Let me know if you have issues.

In general, it’s a good idea to:

1. Take mags completely apart.
2. Fully clean the inside of the mag bodies, followers and springs.
3. Sand / file / clip any dingleberries / flashing on followers or mag bodies.
4. Car wax or Teflon spray everything on the inside.
5. Wax or Teflon spray the outside.
6. If needed use a clamp to squeeze the rib for in the middle or upper of the bodies (this is standard practice for the Czechmate 29 round mags.

[CarlK]

“What issues are you having? I am comfortable mag tuning in general. I have experience with tuning different mags. “


Multiple nose-down failures to feed at the rate of four or five per mag (the Sig mags run flawlessly). I did field strip the ProMags and got rid of the sticky grease that was inside. I then cleaned with Balistol spray oil before reassembling. Still no luck…

[JCN]

“What issues are you having? I am comfortable mag tuning in general. I have experience with tuning different mags.

Multiple nose-down failures to feed at the rate of four or five per mag (the Sig mags run flawlessly). I did field strip the ProMags and got rid of the sticky grease that was inside. I then cleaned with Balistol spray oil before reassembling. Still no luck…

That’s what happens with Czechmate big sticks when it necks down from double to single stack.

So I did the same pinch of that area on the control ribs.



It helps bullets keep feeding instead of diving.

If you want to send them to me I can tune them if you’re not interested in doing it.

[Blades]

Yes. Me. I like the Wilson better.

I may need to try one to see if I like it more than my Boresight grip.

[JCN]

Found some cheap but cant adjustable P365 double pouches.

This would be my gaming rig.

[JCN]

Also saw these:



Which are obviously too long for even open.

But what if I cut it down to 170mm…

Looks like the tabs would be pretty easy to notch and bend.



Could I make a 23-25 round magazine?

Is it worth the hassle over the 20 round?

Would I get to use a Dremel?

Muahahaha

[Up1911Fan]

Just got one of my Razorback modules back from Boresite, where they added the " heel grip enhancement ". It's hard to capture the difference in photos, but is readily apparent when handling it. Fills my hand out much better, and indexes a little better when going from a Razorback'd G19 to the P365X. Need to get this one cut for a 507K, but may wait to see if the new enclosed version becomes available with the 2MOA dot.

[vandal]

Wow that looks even better. I may have to send mine in to have that mod added. Trying the Wilson grip module now though which adds to bottom rear of the grip a bit as well.

This thing is looking more and more like the Walther PPS M1 Grip. Not a bad thing -- I think I benefit for a grip with more "front-to-back" than "side to side".

[D-der]

I'm liking the Wilson module a little better than the Razorback,
the heel enhancement looks like a significant improvement but,
but likely not enough so that I'd want to have that much tied up in
three 365 modules.