Last edited by holmes168; 08-27-2017 at 01:06 PM. Reason: needed to add the word NOT as in NOT in GJM's class.
This country needs an enema- Blues approved sig line
I replaced the gen 5 slide stop with the my gen 4 oem slide stop lever and trigger pin as you mentioned Tom. 200 rounds and worked perfectly, I will still test further but so far no slide lock induced from me with my support hand, and no premature slide lock. I also used the minus connector and again no issues. Tested with lyman guage after another 200 rounds and no difference, it seems that the stock connector is good to go, trigger pull is consistently in the 4.12 - 4.14 range for me.
Glock was introduced 36 years ago and I think they finally reached perfection. Not kidding, the accuracy of this gun for me is ridiculous. Whatever they did with the barrel, for me it's like shooting with a match grade barrel. It's so good for me that I really don't want to replace the crappy plastic sights because I am so perfectly dialed in. I really don't want to mess with them and may just put nail polish or something on them. The poa/poi for me is placing the dot on the target, not top edge of the front post. But I'm kind of used to that from my sigs so it works for me.
I am at best an avg. shooter. This is at 7 yards and I would never keep my groups in the small square. lucky to hit it even once normally. Even with my rmr it's challenge for me.
This is about 22 yards that I walked off. I was drawing from concealment (aiwb, JMC 2.0) and consistently hitting the steel at around 2 sec. Again, with my rmr not sure I am any better, consistent or fast (at least for me). I loaded 2 mags with 10 rounds and hit 7/10, the first time, ant 8/10 the second. This just doesn't happen for me going that quick.
view from my iphone where I was shooting.
I thought I over paid for this but I wouldn't hesitate to pay $1000 for this at this point. I own 10 sigs, which include legions, 226 tacops, 320's, other glocks and a shield and this gen 5 smokes them all without a doubt for me.
Tom please hurry and configure a gadget and I will request right now the first one off the assembly line. Happy to demo any as well.
I've spent a lot of money on my current 19 with milling an rmr, apex trigger kit, magwell, minus connector, trigger undercut. (see pic in post #50) By the way, the grooves seemed to eliminate that need for me as I have no issues with glock knuckle. This stock pistol is perfectly good to go for me. (sights at this point is optional)
Last edited by Dismas316; 08-27-2017 at 12:32 PM.
Thanks for the write up Dismas. As much as I don't want a glock I might pick up a 19 as I have been wanting to RMR a pistol for a while. Wish they had paddle mag release...
Last edited by holmes168; 08-27-2017 at 03:44 PM.
This country needs an enema- Blues approved sig line
I ran another 200rds. through my Gen.5 19 today. It will not pass the 1911 test and I also got 2 BTF today. One about 75rds. in with AE 124gr fmj. Happened on rd. 14 in a fully loaded mag. The second happened with a box of UMC 115gr. fmj either the 7th or 8th rd. out of a fully loaded mag. I also ran 75 rds. of Fed HST 124gr. End of the 2nd range trip and I am 545rds. into it and have this nice little cut on my pinky from the crescent shaped mag cut out. that thing is razor sharp... I knocked it down last night with some sand paper but it really hasn't helped much.
Last edited by CDFIII; 08-27-2017 at 04:00 PM.
I guess you are right, but it'd be interesting to see some Gen 5 samples tested.
From what I understand, the extractor design is basically the same as previous models.
A SCD-equipped G5G19 is definitely on my short list of future 'one size fits all' pistols for both CCW and USPSA use.
To those with G5s and a trigger pull gauge...can you measure the pull weight in the middle of the trigger where the trigger drop safety pivots? That's where my finger rests when pulling so I'd be interested to see what it measures at that spot as opposed to the bottom of the trigger where the most leverage is. Thanks!
Shoot more, post less...
“Remember, being healthy is basically just dying as slowly as possible,” Ricky Gervais
Is the Vickers floor plate compatible with the Gen5?