Page 3 of 7 FirstFirst 12345 ... LastLast
Results 21 to 30 of 68

Thread: I Load Fast

  1. #21
    Quote Originally Posted by Luke View Post
    Looks like you've gone off the deep end. I recommend stepping back, read a loading book or two, then get you a good single stage and learn what it takes to make ammo.
    Ok, I laughed
    #RESIST

  2. #22
    Site Supporter Hambo's Avatar
    Join Date
    Aug 2014
    Location
    Behind the Photonic Curtain
    Quote Originally Posted by John Hearne View Post
    19 seconds isn't quite long enough for me. How about a two minute video?
    "Gunfighting is a thinking man's game. So we might want to bring thinking back into it."-MDFA

  3. #23
    Time for a hashtag! #BallerReloading
    #RESIST

  4. #24
    Member GuanoLoco's Avatar
    Join Date
    Feb 2016
    Location
    Birmingham, AL
    Quote Originally Posted by Hambo View Post
    19 seconds isn't quite long enough for me. How about a two minute video?
    I had a longer one but it was only at 1800 RPH. When I figured out how to make it work reliably at 2100 RPH I deleted it.

    Next time I fire it up I'll do a better and longer version with some commentary.
    Are you now, or have you ever been a member of the Doodie Project?

  5. #25
    Member Peally's Avatar
    Join Date
    Mar 2014
    Location
    Wisconsin, USA
    I want a running commentary, like a play by play.

    But for reals I'm jealous, that's a killer setup.
    Semper Gumby, Always Flexible

  6. #26
    Member GuanoLoco's Avatar
    Join Date
    Feb 2016
    Location
    Birmingham, AL
    Per requests - a longer video from this weekend's activities.

    Saturday night I reloaded and case gauged about 3100+ rounds solo and Sunday AM a buddy and I loaded 1700- more.

    On the solo run I was pretty effectively loading on the 1050, filling primers and case gauging all in parallel. I did struggle a good while with priming issues, for some reason the press gets moody and primers aren't getting installed. I haven't figure this new issue out 100% yet and yes I've cleaned everything and replaced the blue tip on the primer feed tube - twice.

    Last edited by GuanoLoco; 03-27-2017 at 10:51 AM.
    Are you now, or have you ever been a member of the Doodie Project?

  7. #27
    Site Supporter JM Campbell's Avatar
    Join Date
    Mar 2011
    Location
    Texas
    How is the Nobel working out?


    Sent from my iPhone using Tapatalk
    AKA: SkyLine1

  8. #28
    Member GuanoLoco's Avatar
    Join Date
    Feb 2016
    Location
    Birmingham, AL
    Quote Originally Posted by JM Campbell View Post
    How is the Nobel working out?


    Sent from my iPhone using Tapatalk
    The price is definitely right and availability seems good. It burns very clean, comparable to ETR-7 aka (I think) Maxam CSB-1. Also, low smoke and temperature stable.

    Down sides:
    - It is a rough granular powder with lots of different granule sizes. They are small enough to pour through a flash hole and make a mess if your press fails to insert a primer. This happened a LOT this weekend and is a new issue. In this past priming has been a very reliable operation for me. Larger flake powders do not have this problem. It is dense enough that it doesn't tend to fly out of cases very easily.

    Metering: It has weird settling issues, perhaps caused by the irregular granule size. When I started I was doing 20 throw sets and weighing (3.7 gr x 20 throws - 74gr). After 2000 rounds I checked and the throw had increased to 76 grains! I am used to my final check being VERY stable with ETR-7, which is a round flake. I re-calibrated (I am using a micrometer on the powder bar) and after another 1000 rounds I re-checked and it had crept up AGAIN to about 75.0.

    The next day I re-calibrated before loading and loaded 1700. This time the check after loading was down to 72.4 grains.

    My target power factor is currently 132 (I need 125+), so I am fine with that but it is irritating.

    When I look at the powder measure there definitely seem to be layers of larger and smaller irregular granules. Perhaps shaking up the 0.5 kilo / 1.1 lb powder jugs before pouring them in the powder measure would help. I'll try this in the future.
    Attached Images Attached Images  
    Last edited by GuanoLoco; 03-27-2017 at 11:17 AM.
    Are you now, or have you ever been a member of the Doodie Project?

  9. #29
    Site Supporter JM Campbell's Avatar
    Join Date
    Mar 2011
    Location
    Texas
    Looks like cat litter, did you let Luke in your shop?



    Thanks for the news on the powder. I'm currently loading with CFE Pistol.


    Sent from my iPhone using Tapatalk
    AKA: SkyLine1

  10. #30
    Member Luke's Avatar
    Join Date
    Jan 2014
    Location
    Alabama
    Quote Originally Posted by JM Campbell View Post
    Looks like cat litter, did you let Luke in your shop?



    Thanks for the news on the powder. I'm currently loading with CFE Pistol.


    Sent from my iPhone using Tapatalk
    I resent that.



    I haven't been to guanos man cave in a little while. Other skanks have. Doesn't bother me though. He can do what ever he wants with who ever he wants. It's what ever. I don't even think about it really.
    i used to wannabe

User Tag List

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •