Search:

Type: Posts; User: willie

Page 1 of 12 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    105
    Views
    4,887

    Olong, do you have a Lyman M die, or an other...

    Olong, do you have a Lyman M die, or an other expander which will perform the same task?

    Not everybody knows that Win and Rem use special brass to load wadcutter bullets. The difference is that...
  2. Replies
    17
    Views
    656

    This solution is best. If he can't operate a LEM...

    This solution is best. If he can't operate a LEM trigger, then he is out of the game. The P30 has ambi controls and the interchangeable grip options as stated above. I base my opinion on having shot...
  3. This Ranger ammo functions without failure in...

    This Ranger ammo functions without failure in every 9mm I have tied it in.
  4. Replies
    21
    Views
    1,123

    Reading between the lines, I sense many of us...

    Reading between the lines, I sense many of us support the police but choose not to be identified with them. The term virtue signaling was used. I do not see this term fitting this context. In my case...
  5. Replies
    338
    Views
    38,782

    I think the primer dimple occurred when firing...

    I think the primer dimple occurred when firing pin hit primer when slide was out of battery. I would bet Blue's Hi Point collection on that.😊
  6. I've fired a couple cases of Blazer ammo through...

    I've fired a couple cases of Blazer ammo through various 9mm pistols without problems.
  7. Replies
    55
    Views
    3,261

    Mine was very old.

    Mine was very old.
  8. Remington appeared to have loaded what they found...

    Remington appeared to have loaded what they found on the shelf.
  9. Replies
    37
    Views
    1,266

    Factory lead round nose will not be messy. Be...

    Factory lead round nose will not be messy. Be certain to clean under the extractor star and keep the rod straight up when extracting. One trick that you can try but is unnecessary is applying a thin...
  10. Replies
    92
    Views
    4,276

    This is leading to disarming police on this...

    This is leading to disarming police on this basis. They shoot when they should not, and if they don't have guns, they can't shoot.
  11. Replies
    118
    Views
    3,405

    I never had ballistic gel. For pipsqueak calibers...

    I never had ballistic gel. For pipsqueak calibers like .22's through the 380, I would shoot into cans of dog food. I recorded which rounds would burst the cans and which would not. I lost the data...
  12. Replies
    118
    Views
    3,405

    An interesting thread. The op is not endorsing...

    An interesting thread. The op is not endorsing 380's in revolver or pistol. I don't understand his ballistic data, but like one guy told me when we had the day or two to talk shit on the"festivus",...
  13. Replies
    118
    Views
    3,405

    Sometimes I carry a Ruger LCP with Buffalo Bore...

    Sometimes I carry a Ruger LCP with Buffalo Bore ammo. I replaced the recoil spring with a much heavier one. The little pistol functions reliably, and the hot Buffalo Bore cast bullet loads shoots...
  14. Replies
    16
    Views
    548

    You have a nice revolver that was Colt's entry to...

    You have a nice revolver that was Colt's entry to revolvers made with cheap materials and almost no fitting. They were never popular with l.e. departments or sportsmen. Why? Ruger and Smith had these...
  15. You will receive an older version of yesterday's...

    You will receive an older version of yesterday's Alox of which I remember two. Regardless, what you receive will work. It is messy stuff and smells bad. Only a very thin layer is needed. You might...
  16. The millions of GI 45's had staked on front...

    The millions of GI 45's had staked on front sights. These front sights were small. When larger front sights are staked on, their greater mass is the problem. It provides sufficient inertia allowing...
  17. Replies
    22
    Views
    885

    eves And the revolver was worn out too. S&W...

    eves

    And the revolver was worn out too. S&W told its factory trained armorers that performing action work after having fired the revolver 1000 times gave best results. Light pulls through...
  18. Your lube suggestion is much better. I selected...

    Your lube suggestion is much better. I selected the J paste wax because it would be easier. To the op I say follow this suggestion with the alox. I have this too if the op can't find it. Will share.
  19. Replies
    105
    Views
    4,887

    My advice on wadcutter .38 ammo for defense is...

    My advice on wadcutter .38 ammo for defense is buy a couple boxes of factory ammo, check the rounds for visible abnormalities, and then forget about it. You now have good ammo. I have hammered...
  20. Replies
    22
    Views
    885

    I may have a knee joint replaced in three months....

    I may have a knee joint replaced in three months. I will ask the surgeon if he will use a Dremel Tool. If yes, then I will look elsewhere. I already asked him if he had a favorite night for drinking....
  21. Replies
    22
    Views
    885

    There is nothing new about adding abrasive to a...

    There is nothing new about adding abrasive to a revolver action. One reason this technique is a terrible idea is that the abrasive wallows out axial holes in hammers and triggers. At the same time...
  22. The lube in these bullets is a hard lube that was...

    The lube in these bullets is a hard lube that was selected to stay on the bullets during shipping. That is its best trait. If bullets are .357 diameter, they may lead especially when used with the...
  23. Sounds like the specimen was being infused by a...

    Sounds like the specimen was being infused by a Porti Boy embalming pump adjustable for pressure and output.
  24. Replies
    105
    Views
    4,887

    The question of "truth" is philosophical. My...

    The question of "truth" is philosophical. My belief is that there are no absolute truths other than those we might define in a math equation. But I never argue this point. Eventually, other people...
  25. Replies
    105
    Views
    4,887

    Full charge is a new term for me. I should have...

    Full charge is a new term for me. I should have put it in quotation marks. The term is imprecise. Best practice dictates that we discuss loads in terms of acceptable pressure which is defined.

    I...
Results 1 to 25 of 300
Page 1 of 12 1 2 3 4