Welcome to the pistol-forum.com.

Search:

Type: Posts; User: Wayne Dobbs

Page 1 of 12 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    18
    Views
    763

    Thanks, Gabe. I've shot variations of this drill...

    Thanks, Gabe. I've shot variations of this drill for years and find it to be one of the best drills I can do to keep trigger control at a high level. Doing it strong hand only, support hand only...
  2. Replies
    18
    Views
    763

    VP9 Par time: 0.25 seconds No overtime shots ...

    VP9
    Par time: 0.25 seconds
    No overtime shots

    7 yards: 50 - 5X
    10 yards: 50 - 3X
    15 yards: 49 - 3X
    25 yards: 47 - 2X

    Cumulative: 196 - 13X
  3. Replies
    59
    Views
    2,832

    And if sight movement/adjustment is what you try,...

    And if sight movement/adjustment is what you try, here's the math on how much movement is needed:

    Impact error X Sight Radius (5.55" for your P2000) / Range (in inches)

    So let's say you have a...
  4. Replies
    59
    Views
    2,832

    This is what I was thinking, too, GJM. Looks...

    This is what I was thinking, too, GJM. Looks like middlin' decent groups to me and if a bit of correction can be applied to the rear sight, this may be a winner.
  5. Replies
    29
    Views
    1,379

    Any of us should be happy to say we'd created...

    Any of us should be happy to say we'd created such a body of timeless work as Dr. Fackler. He changed the landscape for all of us who go armed against evil in so many ways. Thank you, sir, and...
  6. Replies
    60
    Views
    5,670

    They're going to stay with core handguns and try...

    They're going to stay with core handguns and try to build those sales again, which were bad. Rifle sales are good right now and the 6920 OEMs are moving like crazy. As for moving and/or dumping the...
  7. RTFM....

    RTFM....
  8. Replies
    190
    Views
    16,131

    Here are a couple of articles from C. E. "Ed"...

    Here are a couple of articles from C. E. "Ed" Harris that are very good regarding wadcutters. In fact this whole site is great reading if you're a reloader or shooter. Harris is one of the great...
  9. Replies
    190
    Views
    16,131

    You can simply use the Lyman data for their solid...

    You can simply use the Lyman data for their solid base wadcutter and be on your way. Two full power (but not +P) loads that I use with the bullet you've shown are 3.5 grains of Bullseye or 4.0...
  10. Replies
    39
    Views
    5,518

    Darryl and I have a bit of inside view on this...

    Darryl and I have a bit of inside view on this due to proximity and some "relationships".

    What is very clear is something I was witness to and participant in that started back about 1991. The...
  11. Replies
    1
    Views
    362

    Just don't do it...at least for a serious use...

    Just don't do it...at least for a serious use gun. They're ok for hobby use, but they aren't made to TDP standards at all.
  12. Replies
    16
    Views
    692

    That McFarland is great in concept, but I've now...

    That McFarland is great in concept, but I've now seen enough of them be undersized and fail gas ring tests, that I've decided the GI rings are the best place to be. If they work in your...
  13. Replies
    16
    Views
    692

    A spare bolt assembly and ideally an entire BCG...

    A spare bolt assembly and ideally an entire BCG is very desirable since the majority of problems you encounter with the system start there. The ability to simply drop in a known quality/performance,...
  14. Replies
    51
    Views
    4,746

    Nope. While folks seem to want an SK version of...

    Nope. While folks seem to want an SK version of the gun, I think you're going to see them take the opposite direction in slide length.
  15. Replies
    39
    Views
    1,583

    GJM, Would you chrono that 4.0 TG load through...

    GJM,

    Would you chrono that 4.0 TG load through a couple of your G19s and advise? I KNOW you have more than one G19!
  16. Your mid-length will run the Federal loads just...

    Your mid-length will run the Federal loads just fine, whether MSR or not. That cheap Russian ammo is cheap for a reason. It does more than just under gas the gun, it also fouls a gas tube very...
  17. Replies
    51
    Views
    4,746

    It's going to be a while before there's a VP9c or...

    It's going to be a while before there's a VP9c or SK or whatever. VP40 is next followed by something else and then maybe a compact. Watch and see...
  18. Replies
    202
    Views
    9,312

    Masterfully written...

    Masterfully written...
  19. Replies
    202
    Views
    9,312

    And Mr. White, you have now proven what happens...

    And Mr. White, you have now proven what happens when you make speed or timers your main goal!
  20. Replies
    202
    Views
    9,312

    That's an ND looking for a time and place to...

    That's an ND looking for a time and place to happen. It's one of those shots by (or in) the strong foot in an encounter...
  21. Replies
    202
    Views
    9,312

    Clean lines means no wasted movement or motion. ...

    Clean lines means no wasted movement or motion. It means moving the gun (or support equipment) in as straight a line as possible during manipulations. It means keeping trigger fingers in register...
  22. Replies
    18
    Views
    1,333

    I would start with a new, high quality extractor...

    I would start with a new, high quality extractor and start over. I think that one is done. Welcome to the world of 1911 witchcraft and magic.
  23. Replies
    202
    Views
    9,312

    Darryl, It all comes back to the triad, clean...

    Darryl,

    It all comes back to the triad, clean lines and staying cognitive.
  24. They did.

    They did.
  25. Replies
    39
    Views
    1,583

    4.4 is rather hot, GJM, although it may be fine...

    4.4 is rather hot, GJM, although it may be fine in AK. I use 4.0 - 4.1 and it works fine. I load the RN projos to 1.125" and truncated cones 124-125s to 1.07".
Results 1 to 25 of 300
Page 1 of 12 1 2 3 4
Logout