1. Yes, the Beretta 92 match hammer will fit the 92 and PX4
2. I've installed 3 of them, 2 in 92s and 1 in a PX4. It makes for a very nice trigger with a very short reset, everything else seems...
Type: Posts; User: cyberiad
1. Yes, the Beretta 92 match hammer will fit the 92 and PX4
2. I've installed 3 of them, 2 in 92s and 1 in a PX4. It makes for a very nice trigger with a very short reset, everything else seems...
In my experience with the "A0" and A1 this is true. I didn't keep my A1 long enough to really break it in but I had to put a relatively substantial number of rounds (I can't remember how many)...
I've only ever used their offerings in 9mm but another vote for SNS, great bullets.
I don't know all the options but the first place I look for grips is LOK. I have their Veloce grips on all my 92s.
F or G? I don't think it matters much if it's a range only gun, personal preference.
Grips? I like LOK Veloce and have them on multiple 92s.
TJIB? If you want to do a little work yourself,...
He press checked twice before starting the stage, right? And I bet when he was done shooting during unload and show clear he ejected the chambered round 4 feet in the air and caught it?
Good for her. Instead of "staying in her lane" she can make her own lane.
I had one of the later 9mm models around the mid-2000s. I never measured it, but the slide seemed to be as wide as a Glock 21, not that that's bad. The grip was too smooth, and I didn't like the grip...
Does Florida-man even know what a Platyus is? I'll wait for the Capybara.
I just read the whole thread, no. At least not yet.
Fill the rails with grease and shoot it
Until recently I had an SRO mounted on a 92XRDO Centurion. The mount works well. It is tall and looks a lot "thicker" from the side than it really is. The factory plate is relatively thin in the...
I had a DPP laying around. I don't intend to carry the gun but I do shoot IDPA and 'outlaw' matches with it.
I've seen a couple of videos where the APX RDO cover plate screws were discussed. I may just be lucky, but I found "nearly impossible" to be "easy." Do not use anything but a 2mm hex bit for the...
I had a 550 for several years and added a Dillon (not DA) case feeder. While it worked, I agree with you that if you want a machine with a case feeder it's better to get a machine designed to work...
Look at the 5th picture here https://blog.gritrsports.com/m11-little-gun-that-could/
If your Sig has a pinned in breech block it has a carbon steel slide and internal extractor and I'm virtually...
How old is your P226? Does it have a carbon steel slide with an internal extractor or a stainless slide with external extractor? Depending on how old it is I think it's possible an RXP or Pro Cut...
I exchanged emails with Tony Mayer of JM Custom Kydex and he is going to be making holsters for the APX A1 soon. I've ordered the R/C OWB, which is my favorite range holster (I have 4 or 5 of them),...
The DPP manual says M4x.7x15.8, same as on the Battlewerx page. Leupold will send you a set free. I called a couple of months ago and was told something to the effect that it's not worth the cost to...
The rail is different, the A1 rail is much more 'pronounced.' The angle isn't the best but you can see the frames side-by-side in this video https://youtu.be/WNGCHShHdmM
I just put my A1 slide on...
You may know this already but unless the holster maker specifies the APX A1 I would be careful. I have both the 'A0' and A1 and the A1 will not fit a kydex holster made for the A0. The rail is...
I read that as 'embedded RNA.' The Hololsun not only emits trackable EMF but it can also modify your DNA.
I just put an R1Pro on my PX4 today. The PX4 has the 'v1' LTT MOS cut, not the newer one. I used the MOS-to-R1P plate from Sig. I did torque to 28-30 inch pounds as stated in the manual and did not...
Over the top. It's just a gun for fuck's sake.
So do I. I have the GGI SRT, hammer strut and 17lb mainspring in my P229 and I prefer it to the LTT TJIB. In particular the newer trigger bars (Wilson and LTT) cause the trigger to break much farther...