Search:

Type: Posts; User: Wheeler

Page 1 of 12 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    61
    Views
    3,095

    You missed that part about reading the article...

    You missed that part about reading the article first didn't you?

    ďÖI know there is common ground that already exists, and because I believe that common ground represents a huge opportunity to do...
  2. Replies
    11
    Views
    458

    The story I've heard a couple of times is these...

    The story I've heard a couple of times is these were built for a largish European police agency that was familiar with the Sig pistols and wanted a decocker that was the same. I recently saw one go...
  3. All the best plans require cash and a pickaxe......

    All the best plans require cash and a pickaxe... :)
  4. Gotcha. Thanks for the reply.

    Gotcha. Thanks for the reply.
  5. Replies
    41
    Views
    4,320

    Iím reviving this thread out of curiosity as to...

    Iím reviving this thread out of curiosity as to how the DpX HEST folder performed.
  6. How about a four year update? :)

    How about a four year update? :)
  7. Most revolvers will bind if the primers aren't...

    Most revolvers will bind if the primers aren't seated fully long before the hammer has a chance to fall and have a light strike.
  8. I've used CCI quite a bit for my IDPA loads for...

    I've used CCI quite a bit for my IDPA loads for .38 Special with rarely a problem. Are you running reduced power or old main springs?
  9. Replies
    35
    Views
    1,503

    S&W doesn't listen to end users. They listen to...

    S&W doesn't listen to end users. They listen to distributors. They don't want to retool a line to make a new Model 12 unless someone makes it a cost effective decision for them.
  10. Replies
    35
    Views
    1,503

    Claude Werner approaches a S&W rep in regards to...

    Claude Werner approaches a S&W rep in regards to this very thing. Iím not sure what their response was.
  11. Replies
    24
    Views
    1,370

    .38 S&W Special Ctg is the proper name for .38...

    .38 S&W Special Ctg is the proper name for .38 Special.
  12. Replies
    62
    Views
    4,956

    Funny how the actual article sort of put that to...

    Funny how the actual article sort of put that to rest.
  13. Replies
    35
    Views
    1,503

    That's true. There are a LOT of stories out...

    That's true. There are a LOT of stories out there. :)
  14. Replies
    35
    Views
    1,503

    I shot two seasons of IDPA with a 12-2 running a...

    I shot two seasons of IDPA with a 12-2 running a 158 grain +P load that I used to run through a CS1. That was roughly 3000 rounds in matches. When I sold the pistol back to the guy I bought it from...
  15. Beretta says that promo code is invalid.

    Beretta says that promo code is invalid.
  16. That is weak logic. You need remedial enabling....

    That is weak logic. You need remedial enabling. :)
  17. Replies
    16
    Views
    1,170

    Iíve been using Knipex tools at work for several...

    Iíve been using Knipex tools at work for several years now. They are top notch.
  18. Replies
    79
    Views
    4,995

    Those electricians are shady by nature.

    Those electricians are shady by nature.
  19. Replies
    79
    Views
    4,995

    So what trade were they in?

    So what trade were they in?
  20. Replies
    90
    Views
    3,873

    Best group thus far is 1.4" at 100 using CCI...

    Best group thus far is 1.4" at 100 using CCI Standard Velocity. I haven't played with it much as I've decided I need a scope with some form of BDC on it. I'm not much of a precision shooter but I...
  21. Replies
    27
    Views
    1,714

    The original comment and my reply was about...

    The original comment and my reply was about slaughtering pigs, not about facing them on their turf, just so there's no confusion.
  22. Replies
    90
    Views
    3,873

    I'm running a 3-9x50. That's a pretty large...

    I'm running a 3-9x50. That's a pretty large objective bell, I had to remove the rear sight for clearance.
  23. Replies
    90
    Views
    3,873

    I have no issues getting a proper cheek weld...

    I have no issues getting a proper cheek weld with my CZ Standard, which came with iron sights. There is such a thing as low and no rise rings...
  24. Replies
    27
    Views
    1,714

    They were known to hang out around the various...

    They were known to hang out around the various ranges and look for scraps from the MREs and throw aways from the mermite containers. Whenever we would do field problems we had to be on the look out...
  25. Replies
    27
    Views
    1,714

    When I was in the National Guard we watched a hog...

    When I was in the National Guard we watched a hog walk across our area while on the live fire range for Bradley IFVs. The hog went inside a vehicle with an open gate where two guys sleeping, started...
Results 1 to 25 of 300
Page 1 of 12 1 2 3 4