Search:

Type: Posts; User: Spartan1980

Page 1 of 12 1 2 3 4

Search: Search took 0.02 seconds.

  1. I've not shot that specific bullet but I've shot...

    I've not shot that specific bullet but I've shot many thousands of Hi-Tek coated bullets in .38 short colt, 9mm, .40SW all the way to .45ACP. The Hi-Tek coating is the best thing since sliced bread...
  2. NASCAR has been fully on board with the democrat...

    NASCAR has been fully on board with the democrat agenda for years. This is just them going left in lockstep with their brethren. They lost me years back when they mandated unleaded ethanol fuel in a...
  3. I know this is almost a year old, but it's really...

    I know this is almost a year old, but it's really getting hard to tell what the hell is going on. Mixed signals and all from the kneejerk media. The AR market is utterly flooded with AR stuff, which...
  4. Well FWIW, I'd rather have a 1-7 just for the...

    Well FWIW, I'd rather have a 1-7 just for the capability of shooting heavys. But I really think the twist rate thing is overblown. If one needs to reach out and hit hard out past my rifle's...
  5. Replies
    62
    Views
    1,352

    Pretty good plan. I would echo BE86 and would go...

    Pretty good plan. I would echo BE86 and would go that route over Unique. It has a practically identical burn rate and can load from .25ACP to .44Mag. It's also flash suppressed. It shares chemistry...
  6. I have one of the early M&P15 1-9 rifles and it's...

    I have one of the early M&P15 1-9 rifles and it's a 1 MOA rifle with Federal M193 and my Hornady 55 FMJBT handloads. It's my goto rifle. Never an issue and it'll ping an MGM flasher at 300 yards all...
  7. Thread: Hernias

    by Spartan1980
    Replies
    43
    Views
    1,760

    I'm in this club. I had a left inguinal done...

    I'm in this club. I had a left inguinal done about 23 years ago. Funny thing about mine was that it was a pretty large tear and I had ZERO pain with it. I only went to the doc because I noticed it...
  8. Replies
    7
    Views
    226

    I got a few similar too. My dad once got a...

    I got a few similar too.

    My dad once got a deal on some new cheap shells from Mexico back in the '70s. About half of them came out on fire as they evidently didn't use a retardant on them. Every...
  9. Replies
    14
    Views
    624

    No experience with the 1301 but with the M2...

    No experience with the 1301 but with the M2 spaghetti blasters, my experience has been that they don't need much. Keep them lubed and they run. Keep the mag tube clean/dry and they run. All the crud...
  10. Replies
    61
    Views
    3,899

    N Frame with a recessed cylinder. Just like God...

    N Frame with a recessed cylinder. Just like God intended.
  11. Replies
    31
    Views
    6,133

    Can you describe his measurement/fitment process?...

    Can you describe his measurement/fitment process?

    I ask because like the O/P I'm not real interested in paying the coin for originals, and even if I did I think kittens might die if I put them on...
  12. Replies
    9
    Views
    499

    That right there is the key I think.

    That right there is the key I think.
  13. Replies
    9
    Views
    499

    I've thought about going this route a zillion...

    I've thought about going this route a zillion times. There are definite advantages and the Hornady measure is the one thing I miss from when I was loading on a LNL AP (yes, I made that mistake...
  14. Replies
    42
    Views
    3,716

    It was actually an idea born out of necessity. I...

    It was actually an idea born out of necessity. I have a buddy with an automated 1050 setup specifically for 9mm brass prep. He has it decap, swage and he has a laser on it to sort out the .380. Then...
  15. Replies
    42
    Views
    3,716

    I had great luck with Surface Solutions, Inc. I...

    I had great luck with Surface Solutions, Inc. I had the pvd coat every Dillon powder funnel I own. They did them all for a flat fee that was very reasonable.

    https://www.tincoat.net
  16. Sooo... Back to the O/P. Oklahoma AG's are...

    Sooo... Back to the O/P.

    Oklahoma AG's are notorious for shaking down big corporate. Don't matter which letter they have next to their name, they're all the same.

    My dad took opiates for...
  17. Replies
    32
    Views
    1,630

    I've always avoided energy drinks mostly because...

    I've always avoided energy drinks mostly because I just don't care for the taste, don't trust the ingredients and I get what I need from coffee.

    After looking into this brand I may re-evaluate....
  18. Replies
    23
    Views
    1,086

    Well, S&W forged internal, no-lock revolvers...

    Well, S&W forged internal, no-lock revolvers aren't rare either and have you seen the prices on them lately? But that out of the way, your gun looks to have what I call "honest wear". I.E. it ain't...
  19. Look at it like this. Your question is about...

    Look at it like this. Your question is about reciprocity.

    Oklahoma has the SDA permit. Other states have their own which is substantially the same, therefore they reciprocate.

    If you don't have...
  20. Replies
    3
    Views
    326

    Thanks! It's on my watchlist for later.

    Thanks! It's on my watchlist for later.
  21. Replies
    25
    Views
    573

    For streaming live radio, iHeartRadio is good....

    For streaming live radio, iHeartRadio is good. For just music I just use iTunes for the CDs I've imported and Amazon. I don't need much!
  22. Replies
    38
    Views
    1,496

    Man that ain't bad with a 2.5" gun. Not bad at...

    Man that ain't bad with a 2.5" gun. Not bad at all, especially shooting major in it.

    Watch reaching over the barrel to eject, you'll get a DQ at a major and some locals in my area.

    If you...
  23. I wonder if Wayne is hanging on because if he did...

    I wonder if Wayne is hanging on because if he did step aside, that it would be perceived as an admission of guilt? That guy could have stepped down, took a 6 month vacay, then got another cushy gig...
  24. Replies
    43
    Views
    1,914

    When I bought my Crosstrek, they didn't have a...

    When I bought my Crosstrek, they didn't have a used Forrester or Outback on the lot and only a couple of new ones.

    Never thought I'd get there, but leasing is looking better and better. Just...
  25. Replies
    25
    Views
    1,747

    I know a guy that scrapped a conex box of mostly...

    I know a guy that scrapped a conex box of mostly 9mm brass. He literally had a ridiculous amount. It wouldn't sell even at scrap prices.
Results 1 to 25 of 300
Page 1 of 12 1 2 3 4