Search:

Type: Posts; User: Pnut

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    70
    Views
    7,595

    Sticky: Quick question RANGERBOB…. Have you had any...

    Quick question RANGERBOB…. Have you had any problems with the bands and barrel heat? I have no experience with production Ranger Bands. I go cheap and make my own with cut up bike inner tubes.
  2. Replies
    6,046
    Views
    2,014,849

    Thank goodness I’ve resisted the urge to drop $...

    Thank goodness I’ve resisted the urge to drop $ on an aftermarket follower! I did however copy someone’s idea here to drill a larger hole in the follower for a tactile verification of an empty gun!
  3. Replies
    0
    Views
    94

    Anyone still using Norrells MolyResin?

    MolyResin got brought up in another thread, but I didn’t want to get off topic so I decided to start this one. I used The stuff a lot 10-15 years ago, but the haven’t heard about it much lately. I...
  4. Good to hear people are still using MolyResin! I...

    Good to hear people are still using MolyResin! I used it years ago and loved stuff! I used the heat cure stuff too and I liked how it goes on real thin. You should sandblast the thing to be...
  5. Replies
    6,046
    Views
    2,014,849

    Couldn’t you run it without the clamp? I run my...

    Couldn’t you run it without the clamp? I run my factory cover without one with no problems… I do check the tightness every so often just in case, but so far it hasn’t moved under recoil.
  6. Replies
    70
    Views
    7,595

    Sticky: One other advantage I see with this setup is if...

    One other advantage I see with this setup is if you run a clamp. The factory clamp tends to move around under recoil unless you really tighten it down. The description on this says there is a...
  7. Replies
    7
    Views
    291

    Thanks everyone… the old battery pack is off to...

    Thanks everyone… the old battery pack is off to the battery recycling spot.
  8. Replies
    7
    Views
    291

    Repurposing 18650 batteries???

    My cordless vacuum stopped working because the battery pack went bad. I decided to open up the pack to see what was in there… turns out it was comprised on eight 18650 cells.

    I fave a few...
  9. Thread: gun vise

    by Pnut
    Replies
    6
    Views
    364

    I was looking at that vise too, but the cost is a...

    I was looking at that vise too, but the cost is a little too much for me. It has some cool unique features which should make certain tasks easier. But I’ve been doing fine with my cheap Harbor...
  10. Replies
    10
    Views
    443

    I had an older Surefire Scout light that ran...

    I had an older Surefire Scout light that ran their first gen LED head. It ran on 2 CR123. I tried running 2 rechargeable RCR123, and killed the head.

    As far as I remember, SF now offers...
  11. Replies
    10
    Views
    460

    My buddy was showing me his latest light purchase...

    My buddy was showing me his latest light purchase and it was tiny. I don’t have experience with the brand, Olight, so I can’t attest to quality or durability. Butbthe light was small, bright and...
  12. Replies
    10
    Views
    460

    I ran into the same problem with an AR pistol...

    I ran into the same problem with an AR pistol build. I wanted to run an X300 on right side (I’m right handed) with a tape switch at 12 o’clock. It works, but I wish I had a little more room for my...
  13. Replies
    6,046
    Views
    2,014,849

    Like I said earlier, I have no dog in the fight. ...

    Like I said earlier, I have no dog in the fight. Personally, I have the factory 7 rounder with the retainer removed and no mag clamp. The retainer is out so I can actually run 7 rounds. I ditched...
  14. Replies
    6,046
    Views
    2,014,849

    I’m no engineer, but here’s my thinking… with...

    I’m no engineer, but here’s my thinking… with the spring pushing against the mag extension, the ball detent will be less effective at doing its job because the mating surface is being forced away...
  15. Replies
    6,046
    Views
    2,014,849

    I don’t have a dog in the fight, but here’s my...

    I don’t have a dog in the fight, but here’s my understanding/interpretation of the situation…

    The FACTORY 7 round tube extension cover will be less prone to coming loose if used WITH the factory...
  16. Replies
    304
    Views
    24,571

    I know LASD and LAPD allow the carry of...

    I know LASD and LAPD allow the carry of Staccatos. I’m curious if the Springfield will make it on their list of authorized duty weapons.
  17. “FORM OVER FUNCTION” I hear you on that! For...

    “FORM OVER FUNCTION”

    I hear you on that! For me, most of my guns are TOOLS… not jewelry!!!
  18. Nice work! Did you leave the seam in the back...

    Nice work! Did you leave the seam in the back strap as-is after your mod or are you going to stipple it to hide the cuts?
  19. Replies
    304
    Views
    24,571

    Just found this thread so excuse me if my...

    Just found this thread so excuse me if my question has already been answered, but it the Prodigy’s frame made by Springfield or is it sourced out by STI/Staccato?
  20. Replies
    6,046
    Views
    2,014,849

    The SKU# is 913200213

    The SKU# is 913200213
  21. Replies
    6,046
    Views
    2,014,849

    Good news! I guess after all my phone calls, the...

    Good news! I guess after all my phone calls, the USPS got their stuff together. I checked the tracking this evening and miraculously, it arrived at the local post office and should be delivered by...
  22. Replies
    6,046
    Views
    2,014,849

    USPS rant!

    After hearing of some having issues with the gas system O-ring, I decided to order a couple to have around just in case. I ordered through Brownells who shipped them on the 9th. It’s now the 24th...
  23. Replies
    6,046
    Views
    2,014,849

    I’m curious… are the “coated” Barettas coated on...

    I’m curious… are the “coated” Barettas coated on the inside and outside surfaces?
  24. Replies
    6,046
    Views
    2,014,849

    Nice that it’s non rotating… I was basing my...

    Nice that it’s non rotating… I was basing my assumption on the pictures on their web site.
  25. Replies
    6,046
    Views
    2,014,849

    I was looking at their charging handle and it...

    I was looking at their charging handle and it looks like it might be a spinner…
Results 1 to 25 of 300
Page 1 of 12 1 2 3 4