Search:

Type: Posts; User: JCN

Page 1 of 12 1 2 3 4

Search: Search took 0.14 seconds.

  1. I really want to do this, but work schedule wonít...

    I really want to do this, but work schedule wonít allow it. Hopefully this will be offered again next year?
  2. Replies
    37
    Views
    2,290

    Iíll make the side comment that sometimes...

    Iíll make the side comment that sometimes shooters have limited grip strength and use racking aids. Iíve recommended those in the past. The other way to get around that is with a weaker recoil spring...
  3. Replies
    207
    Views
    39,948

    I hear ya man, for my carry gun I opted for an...

    I hear ya man, for my carry gun I opted for an accurate set of iron BUIS just in case.

    And then just treat the dot as gravy over irons.

    But at least the impact and reliability testing of the...
  4. Replies
    219
    Views
    21,610

    Tell your friend Iíll trade him. I have two PM9s...

    Tell your friend Iíll trade him. I have two PM9s just gathering dust since the P365 came out.
  5. Replies
    136
    Views
    7,097

    Okay, I like it.

    https://youtu.be/Tyu4YOQWCoc

    Okay a couple reps with a camera in the way (so not my fastest).

    Reloading 38 special.

    The cylinder release shape works well rolling off the gun shift....
  6. Replies
    136
    Views
    7,097

    Revolver supply cylinder release

    70464

    7046570466

    The standard Hogue is the silver one.

    The revolver supply one actually feels like delrin or polymer. Itís not metal. But the gripper nubs do a great job of grabbing my...
  7. Replies
    1
    Views
    362

    ďThe proposal goes on to suggest several other...

    ďThe proposal goes on to suggest several other rule changes. It would change how silencers are regulated by requiring only the outside tube to be serialized instead of each individual part.Ē

    Well,...
  8. I will say like the above people, I have taken a...

    I will say like the above people, I have taken a Dremel with a stone attachment to break up various hot spots on parts of my guns and things. Itís a tool, not a showpiece. Donít care about the...
  9. Build calluses.... you should see the tumor sized...

    Build calluses.... you should see the tumor sized calluses I have on those same fingers from the Shadow 2. :D

    Alternately, tape your fingers in those areas with bandage / sport tape.

    Or use...
  10. Thread: Ammo deals!

    by JCN
    Replies
    1,625
    Views
    328,380

    Sticky: Bone Frog with $500 cases of 1000 steel Tula ...

    Bone Frog with $500 cases of 1000 steel Tula

    https://www.bonefroggunclub.com/collections/ammunition/products/9mm-115gr-tula-fmj-ta9?variant=39266071314501
  11. Replies
    55
    Views
    2,138

    Nope, not a dumb question at all! I do not! If...

    Nope, not a dumb question at all! I do not!

    If the barrels don't swap in easy, I'm sending it out and forgetting about it.

    But if it works even kind of, it'll let me figure out what kind of...
  12. Replies
    207
    Views
    39,948

    All alpha except two charlie

    https://youtu.be/OJkbxio89DU

    This is my "confirm vision" speed. I had exactly enough rounds that I couldn't make any make up shots, so I went at a pace that I made sure I saw what I needed from...
  13. https://youtu.be/Lz0xULQIaSU

    https://youtu.be/Lz0xULQIaSU
  14. Replies
    55
    Views
    2,138

    Thanks! Hopefully the barrel thread pitch is...

    Thanks! Hopefully the barrel thread pitch is appropriate between new and old N frames. The other parts Iím not concerned about.



    But thereís a lot of incomplete information out there. The...
  15. Replies
    55
    Views
    2,138

    Also, I posted in my other thread but I ordered...

    Also, I posted in my other thread but I ordered this one too:

    70428

    If the barrel threading works out, I figure I might try my hand at cutting and crowning the cheap barrel and then move on to...
  16. Replies
    55
    Views
    2,138

    Need more Kelly Lebrock 70427

    Need more Kelly Lebrock

    70427
  17. Replies
    136
    Views
    7,097

    Big thanks to OlongJohnson for the spare...

    Big thanks to OlongJohnson for the spare Nightguard cylinder!

    This way I can mess with my original and push it to the extreme of chamfering and still have a backup if I go too far...

    70426
  18. Replies
    10
    Views
    530

    Would love a review when you get back! Enjoy!

    Would love a review when you get back! Enjoy!
  19. Replies
    136
    Views
    7,097

    Oh Iím dumb. But itís fun working on dumb...

    Oh Iím dumb. But itís fun working on dumb projects sometimes.

    I still drive a manual transmission car for fun too.
  20. Replies
    136
    Views
    7,097

    jetfire I really enjoyed reading that article,...

    jetfire I really enjoyed reading that article, thank you for the link!

    I ordered the cheap barrel for experimentation and cutting. And this one for pretty factor if it seems to work out.

    70424
  21. Replies
    55
    Views
    2,138

    Tinker tinker

    70419

    Well, for $60... why not?

    Such a bizarre project, but Iím enjoying learning.
  22. Replies
    55
    Views
    2,138

    70417 Okay, I think I answered my own...

    70417

    Okay, I think I answered my own question. The width of the N-frame barrel threads looks to be significantly larger than the K/L frames.
  23. Replies
    55
    Views
    2,138

    Thanks! It used to drive my parents nuts when I...

    Thanks! It used to drive my parents nuts when I would disassemble everything growing up. But I learned a lot and the curiosity has never gone away. I feel like it serves me well to always question...
  24. Replies
    55
    Views
    2,138

    So lead time on having custom work done might be...

    So lead time on having custom work done might be a couple months...

    70413

    Because I have more money than good sense, and I like tinkering and like getting into stuff for more complete...
  25. Replies
    55
    Views
    2,138

    Iím open to input. I was thinking this would...

    Iím open to input. I was thinking this would mainly be for a 9mm gun for ease of reloading over ballistics.

    At >3.5Ē Iíd be very tempted to leave it as a 357...

    I have a model 66 in 4Ē and a...
Results 1 to 25 of 300
Page 1 of 12 1 2 3 4