Search:

D&L is good to go I’m sure, I just got a M&P back from him with the J-frame sights. He would probably fit the front sight to match your load if you sent your carry ammo.

https://www.surefire.com/lm2-b-bk/
This is what you seek to update the Forend to 1,000 lumens. I love the older Nashville Scattergun Remingtons, they are usually built on 870 Magnum/Police Magnum...

I was fourth or fifth from the left.

I was also in the Janesville Pistol class in August and plan on being in this class. Thanks for hosting him.

Try pushing up on your slide stop, you should hear a click and then try to assemble.

On my KKM barrels/comps I degrease and then install the comp itself with a small amount of red loctite as it’s large enough that I don’t have to worry about stripping anything after a little heat...

I make gross adjustments at 10 yards to get a rough zero and then refine/confirm at 25 freestyle/unsupported. It seems to be the most expedient way I’ve found. The zero is a never ending process to...

The Edgar Sherman Design magwell is probably the best I’ve used so far. However my experience has been limited to the Zev and SLR and ESD in Gen 5 Glocks. I wish that ALG and Raven will eventually...

86050

The Agency comp will work with Apex gunsmith fit barrels, I’m pretty sure the Parker mountain would fit too based on my other PMM comps.

I have the one port JTTC on a G17 and it fits in all of my G34 holsters, I’d say it’s less than 1/8” longer than a G34.

I have a few hundred rounds of it and wanted a little more oomph to get performance out of the comp and the P365X only has a 3.1” barrel. I probably will wind up switching over to 124 +P HST or Gold...

I’m sure there will be some recoil/muzzle flip reduction, but not as much as hotter 124 gr ammo. I typically carry 147 gr Speer G2 in my Glocks, but zeroed my P365X w/ 135 gr +P Critical Duty.

I ran about 400 rounds through my PMM P365X the other day w/ Blazer 115 gr, Federal 115 gr, Norma 124 gr, Norma 124 gr Envy PCC, and Hornady 135 gr Critical Duty. I had no issues which actually...

P365X w/PMM Micro Comp and Blazer 115gr FMJ @ 25yards

85019

That’s what I am assuming, I haven’t weighed them yet or really studied if there’s as difference in blast chamber or port size yet.

I have one waiting on my slide to get back from ATEI, should be less finicky than other comps and only increases the length of 19/45’s to 17 length. Interestingly, according to PMM’s product page it...

I believe that Impact Machine is run by Scott Milam, the son of the owner of Cajun Gunworks David Milam. He works closely with Brandon Bunker, one of the best 1911 gunsmiths around. I noticed his...

Some factory guns can be surprisingly capable though. I bought a P320 X-Vtac a couple of months ago and installed an CHPWS filler plate, HRS RMR and an Apex flat trigger. I did not really like the...

Not to derail this thread but that Gen 5 17 would not shoot better than 95/96 at 25 on a B8 with numerous different loads when I’m consistently able to shoot mid-high 90’s with other Glocks, 320’s,...

These are a few of the groups I’ve shot with my Chambers gun, it is a laser and makes shooting high-90’s at 25 almost effortless.
819288192981930

I almost exclusively shoot 10 shot strings and never exceed 30 seconds. I will vary it depending on what I’m attempting to accomplish. Slowfire for me is usually untimed but somewhere between 20-30...

5 Shot Leather can do the SME with the DCC Monoblock or he may be able to do the Sentinel for a Hi-Power?

Figured it was the time to teach my kids to shoot, so that gave me the excuse to buy a .22 pistol. Zeroed today with an Aimpoint TL I had lying around. Target was at 25 yards freestyle unsupported...

Thanks, It took a lot of work to be able to on a somewhat consistent basis. I can’t with iron sights, but I’m able to shoot consistently >95/96 and at least a couple of hundreds on each range...

Couple of runs at 25 with Boresight Wilson module X5/ACRO and a Chambers PHATWMG-NF.