Search:

Pferd makes the 2-n-1 for Stihl. Keep in mind Stihl uses a 13/64 file for their 3/8s chain, not 7/32. It's just 1/64 smaller and I have used them on Oregon chain. It works ok but I would rather use a...

Just for reference, my 3 inch Python weighs 2 ounces more than my GP100 WC. They are all heavy....

200+ rounds of reloads and/or cheap target ammo to verify function, adjust sights and to see if any grip mods need to be done. Once that has been accomplished, from a clean gun I will shoot intended...

I did not need to know about this.



I did not need to know about this.

MBW has a question asking it the bullets are going to be used in a revolver ,and I emailed asking for clarity. If anyone ever questions their quality, direct them to the response I got: It just gives...

Well, I've slugged my barrel. There is just something creepy about driving a hunk of metal down a barrel. Anyway, it measured out to .431 and I have an email in to MBW to see what they recommend.

I have used a fair bit of cast bullets in this gun including some big SWCs, and there is no suppressor. The wide flat points that I'm looking for seem to gas checked from MBW and nowhere else. I'm...

Because a wide flat nose has been recommended, I have found these 3 that I want to try, 44 Mag, LBT, 280gr, WFN-GC - Montana Bullet Works, 44 Mag, LBT, 260gr, WFN-GC - Montana Bullet Works, 44 Mag,...

I have used a lot from Missouri Bullet Company and snscasting. No complaints on either.

It was at least an hour after my incident when I puked into an Idaho Falls Pd trash can. It was another 30 minutes until I was able to regain composure and continue with my statement.

A bullet gets pulled by forces in recoil so a pulled round will not be in the forcing cone. A pulled round does have the potential to be a squib and that causes a bit more problems.

I had one of my reloads pull in my LCR. Round #5 stopped cylinder rotation. No drama, turned the gun vertical, hit the ejection rod and very slight pressure to dislodge the pulled bullet. Dropped in...

I do not have a .357 rifle yet, so I don't have experience there. However, I do have experience with a .44 mag rifle and have been doing a lot of research ISO a better hunting bullet for a .44 mag...

I have had coyotes and black bear in my yard and I frequent the woods where feral hogs roam. The likely hood of having to deal with a bear is low but not zero. Coyotes are invasive to WNC and need to...

Since most of my threats run on 4 legs, 158 SJSP or 170 SWC loaded in .38 cases to .38-44 velocities. A 2 legged varmint isn't gonna notice that I'm not using a "defensive" round.

If I have read this right, you shot 359 rounds of magnum ammo plus 38 of .38 in one range session?! WoW, you go girl...:cool:

To answer what has already been answered, yes, its carbon build up....

This is where I screwed up. I put the pin across a hole in my armorer's block and hit it with a big punch making a not so gradual bend. I wish I had the skills to spline, that seems to be a more...

All 3 of my GPs did this. The correct way is to source oversized pins, I didn't have any patience for that so I used 2 methods found on the interweb.

1 - take the pin out and slightly flatten one...

I did some work on Hornady's ballistic calculator (checked results against 2 others) using their impact velocity chart and came up with some good theoretical data.


The 200g XTP has a max impact...

I tried the 270g Deep curl, out of a 5 shot group with 3 different charge weights and 2 different powders, total of 6 groups, I could 3 or 4 in 1 1/2 then the fliers would leave you thinking Ray...

I've seen those images and they do cause concern.




I like duck.

I've used hard cast in the past and it is not lost on me. I've pulled fired bullets out of a red oak stump that I use as a...

I took both of my north Georga bucks this year using my 1894 .44 mag. The load is a 200 grain XTP on 28 grains of W296. Book velocity shows ~2100fps out of a 20-inch barrel. (now that I have my...

I have used a few hundred of 5 1/2s and ran them through my Rugers and Pythons with no issue. The Rugers, GP100 and SP101 have reduced power springs.
\
As for the primers this is from their...

The best way to get 12 shots of .357 is to have 2 6 shooters, one for each hand.

I have watched this guy too, his shop is about an hour from me never been there tho. He seems to be genuine and honest, but his testing leaves me wondering. Going out and running a tank of whatever...