Search:

Just got 2 from dukessportshop.com and staccato2011.com. Mounted and did some dryfire. Here's the reticle options on a uspsa target at simulated 7 yards.

106273
106275

Here's the correct link to the graphs.

https://public.tableau.com/views/GlockPerformanceTriggerConnectorComparisionwP1Spring/Sheet1?:language=en-US&:display_count=n&:origin=viz_share_link

So I uploaded my trigger test rig data to a public interactive graph. Tested a stock Gen5 trigger and Glock Performance with OEM connectors. They're stock other than about 1000 dry fires to break...

My Glock Performance trigger arrived today so I dusted off my trigger dyno.
The Factory and Timney triggers have less than 500 rounds through them, while the Glock Performance is new out of the box....

Don't tempt me! I thought about milling them shorter. But the front rail would only be about 1/8" long and the slide would impact directly on them instead of the radiused plastic. Probably peen...

The G19 and G26 locking block is unchanged from gen1-5. Unfortunately this won't work. The forward rail section on the G19 frame is cut longer, so the 26 slide won't travel far enough to the rear...

I'm willing to pay a few extra $ for a tight optic fit.
https://www.instagram.com/p/BZKtVaOl8yl

MAC Defense does a fantastic job as well and won't charge you to Cerakote just the cut area if...

I had JagerWerks mill my gen4 G26 about two years ago. Occasionally carried it with the 10 round mag but usually with 12.

I ended up using it on the 2nd day of a vehicle class when the front iron...

Make sure the base of the sight isn't too thick and sticking out past the walls of the slide.. If it is, just file/sand some material off the bottom. Rocksette can withstand high temps, but you'll...

Did you remove the suede liner in yours or just back out the adjustment screw? My P10 wouldn't fit in my 6360RDS with an x300 or TLR1 until I ripped the liner out(rain caused it to swell and lock up...

The Optics Ready slides have relief cuts under the optic mounting screws. However, the included 6-32 x 1/2" long screws may contact the bottom of the cuts. Mine did. You can either file them...

It's a little more involved than a zip-tie or scrap of cardboard, but it's a lot more realistic. It does require a few bucks and a trip to the hardware store.
...

Anyone figure out a way to get 23 rounds to work reliably? I've seen quite a few reports of 22 being the limit for reliable P09/10F mags. I used CZC 140mm extensions in my CZ-75 mags with Grams...

I have the factory ones and the ones from CZC. The OEM plates are steel, about 1oz heavier, and the finish isn't like the slides nitride. It's more like black oxide, while the anodizing on the CZ...

I definitely need to test some 1911s, if only to debunk all the "my X trigger feels just like a 1911" people. But, none of my 1911s have rails to securely mount them to my rig. I may get one of...

Slide is off my carry gun. Runs like a top after some tweaking. Glocks aren’t as plug and play as people think with aftermarket parts. Gold barrel and comp were blems. Had to take a few...

It’s just a 10kg from amazon. I turned a “finger” in the lathe and added a delrin roller bushing.

After seeing so many reviews of triggers and parts that all pretty much sound the same: "Here's the weight, it feels good, the break is crisp, clean reset, etc" I figured it was time to get some...

Sounds like the "opposing forces" reload. My first exposure to it was from Paul Van Dunk.

https://www.youtube.com/watch?v=6B1WiWAH01s

I had the same problem as you at first. I'd anticipate...

I'm planning to experiment with a bargain Glock frame that had been used for stipple practice. Rough up and clean the surface, build up thin areas with epoxy putty, sand to my liking, then cover...

Anything that can help make the experience more enjoyable is a win in my book. It may be a crutch for learning proper grip, but have you considered adding weight under the rail? You could even go...

I put a factory trigger bar on my Agency trigger and it does not contact the striker safety block(factory or Apex). The scallop cut doesn't alter the final height or position of the lifter tab. The...