Search:

Type: Posts; User: HTM

Page 1 of 3 1 2 3

Search: Search took 0.42 seconds; generated 50 minute(s) ago.

  1. Thread: Eligible pistol?

    by HTM
    Replies
    1
    Views
    97

    Carry optics legal ESP legal minus the optic and...

    Carry optics legal
    ESP legal minus the optic and magwell
    SSP may be legal minus the optic and magwell.

    Biggest issue is weight of the gun. Double check the idpa rule book.
  2. Replies
    41
    Views
    13,152

    Carry over locking block from the Gen3/Gen4...

    Carry over locking block from the Gen3/Gen4 G19/G23/G32

    What are the correct torque values for Glock front sights (polymer / steel)?[/QUOTE]

    Hand tight. Easy to strip out the poly sight.
    ...
  3. Replies
    41
    Views
    13,152

    Optional. I always remove it. It's there for...

    Optional. I always remove it. It's there for storage purposes.


    They aren't. People just tend to open the case upside down. :cool:
  4. Replies
    41
    Views
    13,152

    Over the recent years Glock has changed standard...

    Over the recent years Glock has changed standard sight heights. The standard used to be 6.5mm rear with 4.1mm fronts. Now most ship with 6.1mm rear and 4.1mm fronts. That goes for GNS night sights...
  5. Replies
    41
    Views
    13,152

    Top of front sight.

    Top of front sight.
  6. Replies
    253
    Views
    35,197

    What rear sight are you mounting? With the stock...

    What rear sight are you mounting? With the stock poly adjustable sights I installed the 4.9 front to give have more adjustment for elevation. The stock 4.1 hit high at the lowest adjustment.
  7. Replies
    5
    Views
    803

    Good drill ...

    Good drill

    https://uploads.tapatalk-cdn.com/20210421/9334a9af13a22648e86ce19ee31a8b04.jpg


    Sent from my iPhone using Tapatalk
  8. Replies
    214
    Views
    20,341

    You base this statement on what? Sent from...

    You base this statement on what?


    Sent from my iPad using Tapatalk
  9. Replies
    80
    Views
    8,994

    Consistent 2.8lb pull with std dot connector in...

    Consistent 2.8lb pull with std dot connector in my 19 Gen5. Full engagement. Clean reset. Usual firing pin lug drag marks on the cruciform. NP3 coating is a bonus Will continue to track trigger...
  10. Replies
    80
    Views
    8,994

    There is a set screw to adjust pretravel of the...

    There is a set screw to adjust pretravel of the trigger. To assure that the trigger safety properly and reliably resets it may require backing that screw a tad.
  11. Replies
    15
    Views
    1,152

    I've made a few custom case inserts using...

    I've made a few custom case inserts using standard pick n pluck. Even multi layer ones. I found a good tip online a while ago and it has worked well for me.

    Carefully layout and design your...
  12. Replies
    433
    Views
    55,619

    Wayne Dobbs for the win. Sent from my...

    Wayne Dobbs for the win.


    Sent from my iPhone using Tapatalk
  13. Replies
    161
    Views
    11,562

    And another one. ...

    And another one.

    https://www.inquirer.com/business/sig-sauer-guns-septa-ice-misfiring-suits-police-20210227.html


    Sent from my iPhone using Tapatalk
  14. I just got a .22 barrel with 3 bulges. Same lot...

    I just got a .22 barrel with 3 bulges. Same lot of ammo. FYI I have yet to have an ammo company rectify this issue with .22LR ammo. You're likely on your own for the cost of replacement.
  15. I Done Think I Bulged My Barrel (Beretta 92 .22LR Conversion)

    Whether itís a major ammo company, Jim Bobís gun show specials, or your own reloads. Quality ammo companies stand behind their product. Normally they catch the problems before they leave the factory....
  16. I Done Think I Bulged My Barrel (Beretta 92 .22LR Conversion)

    As I have posted before. Bulged barrels are the result of an under charged squibbed bullet getting stuck in the barrel and a fully charged being fired behind it. Often but not always both bullets...
  17. Replies
    161
    Views
    11,562

    Does anyone remember the issue with M&Pís firing...

    Does anyone remember the issue with M&Pís firing if the shooter prepped the trigger then came off the trigger? A known design flaw that while a rare occurrence S&W addressed it in their manual. I...
  18. Bulged barrels are not a result of double or an...

    Bulged barrels are not a result of double or an over charged round. They are the result of an under charged round, a squib, lodging in the barrel followed by a fully charged round. The bulge is...
  19. Replies
    80
    Views
    8,994

    March 2020 supposedly

    March 2020 supposedly
  20. Replies
    23
    Views
    1,924

    You won't believe what broke on my Glunk!

    I know for a fact. I have a good friend that has worked there for a long time. It takes 13 seconds to mill them. They have never been mim and are not today.

    This rumour has mostly propagated by...
  21. Replies
    23
    Views
    1,924

    Glock firing pins are milled. They are not and...

    Glock firing pins are milled. They are not and never have been MIM.


    Sent from my iPad using Tapatalk
  22. This is what you get when you outsource critical...

    This is what you get when you outsource critical parts. You donít control the process start to finish. Plus itís easier to blame the supplier.


    Sent from my iPad using Tapatalk
  23. Honestly this is more concerning than the Hellcat...

    Honestly this is more concerning than the Hellcat story. If all of that work had to be done, how did it get out the door the first time?
  24. Thread: P320 issue in PA

    by HTM
    Replies
    114
    Views
    16,389

    My bad. I didn't see that thread. Please forgive...

    My bad. I didn't see that thread. Please forgive :cool:
  25. Thread: P320 issue in PA

    by HTM
    Replies
    114
    Views
    16,389

    Looks like another lawsuit in progress NH this...

    Looks like another lawsuit in progress NH this time.
Results 1 to 25 of 54
Page 1 of 3 1 2 3