Search:

Type: Posts; User: Mfbpt

Search: Search took 0.00 seconds.

  1. Replies
    1,141
    Views
    128,277

    Check out Ndz’s x macro backstap. They’re made...

    Check out Ndz’s x macro backstap. They’re made of aluminum so you get a little extra weight, not much but a little. The xxl has the exact same feel as the Boresight razorback without the price tag....
  2. Replies
    200
    Views
    13,615

    I’d try one for sure.

    I’d try one for sure.
  3. Replies
    643
    Views
    70,384

    Why wouldn’t you just shorten the screw?

    Why wouldn’t you just shorten the screw?
  4. Replies
    28
    Views
    2,239

    These are by far the nicest I have seen and used ...

    These are by far the nicest I have seen and used

    https://thecncpros.com/products/ols/products/glock-mos-mounting-plate-for-holosun-590t
  5. Replies
    1,141
    Views
    128,277

    I was able to install the magwell on my Razorback...

    I was able to install the magwell on my Razorback with the large backstrap.
  6. Thread: Goon Tape

    by Mfbpt
    Replies
    20
    Views
    9,204

    It really depends on how much you handle the gun....

    It really depends on how much you handle the gun. If you drifire daily with it it may last a month, if it’s not handled a lot obviously it will last longer. You really don’t need a ton on your grip...
  7. It’s the ammo. Those aren’t light strikes. Grab...

    It’s the ammo. Those aren’t light strikes. Grab some S&B or Blazer brass and shoot the shit out of it. Ten bucks says it doesn’t happen again unless you continue using Winchester white box then...
  8. Thread: RDS/MOS accuracy

    by Mfbpt
    Replies
    22
    Views
    4,524

    These just came out yesterday. Machines out of...

    These just came out yesterday. Machines out of steel and basically gives the mos a milled fit.

    https://www.forwardcontrolsdesign.com/OPF-G-RMR_p_224.html
  9. Replies
    40
    Views
    10,553

    I started ordering from Ammoempire. Pretty sure...

    I started ordering from Ammoempire. Pretty sure Sgammo runs it. Haven’t been charged tax yet and prices are shipped.
  10. Sticky: I’d us the vc3 on all the screws. That’s what I...

    I’d us the vc3 on all the screws. That’s what I did on my mos 34 and haven’t had any issues
  11. Sticky: Also I doubt you went over board on the Vc-3. It...

    Also I doubt you went over board on the Vc-3. It will break free fairly easily but it resists loosening from vibrations.
  12. Sticky: I’d do it over and make sure you’re using inch...

    I’d do it over and make sure you’re using inch not foot pounds. Also use quality fastener bits.
  13. I have a Wilson Vickers black rear paired with a...

    I have a Wilson Vickers black rear paired with a Trijicon hd front on my 19x. It’s my new favorite combo for my no optic pistols. I also have the black rear and tritium front on my P30sk. They...
  14. Sticky: They don’t say but I’m assuming it’s 7075. With...

    They don’t say but I’m assuming it’s 7075. With the rmr using 2 small screws to mount aluminum is a poor material to screw into. I see it failing and the rmr flying off. If they would have made it...
  15. Sticky: The C&H plate showed up today. My take on it is...

    The C&H plate showed up today. My take on it is great design but not a good material to use. Their made of aluminum. There is no way I will install this plate on my Glock 34. Mounting the RMR to...
  16. Sticky: Did you even use the sealing plate on the C&H...

    Did you even use the sealing plate on the C&H plate?
  17. Sticky: I did just order one of the C&H plates. They...

    I did just order one of the C&H plates. They look really solid and clean looking. Thanks for the tip
  18. Sticky: I also used the VibraTite Vc-3. I just tightened...

    I also used the VibraTite Vc-3. I just tightened using the short end of the wrench that’s probably pretty close to 15 inch pounds. After 500 rounds nothing has loosened and still seems solid. One...
  19. Replies
    67
    Views
    21,382

    I’m feeling really apprehensive about sending...

    I’m feeling really apprehensive about sending mine in for the so called upgrade.
Results 1 to 19 of 19