Search:

Type: Posts; User: revchuck38

Page 1 of 12 1 2 3 4

Search: Search took 0.07 seconds.

  1. Bullet supply does seem to be loosening up. ...

    Bullet supply does seem to be loosening up. Those SNS bullets seem to be the generic DEWCs that most casters sell, so if we can't get them from SNS there are other suppliers.
  2. Thread: Ammo deals!

    by revchuck38
    Replies
    1,687
    Views
    336,025

    Sticky: AE 9x19 115 and 124-Grain FMJ

    Four box limit, $27/box.

    https://www.federalpremium.com/handgun/american-eagle/american-eagle-handgun/11-AE9AP.html
    ...
  3. Replies
    15
    Views
    568

    FWIW, my experience with this vest was mixed. I...

    FWIW, my experience with this vest was mixed. I used one for several months during a deployment to Afghanistan and the rifle magazine pockets wore through pretty quickly. This was caused by the...
  4. Replies
    21
    Views
    455

    +1. I've shot 700+ of my handloads using swaged...

    +1. I've shot 700+ of my handloads using swaged lead bullets at +P pressures in a class and had no leading because everything fit. The ammo you have is standard pressure stuff, I'd run a box of it...
  5. Interesting .45 Colt Defensive Load from R-P

    .45 Colt 230-grain JHP.
  6. Replies
    460
    Views
    43,750

    Ouch.

    Ouch.
  7. Replies
    460
    Views
    43,750

    Story on the 1911?

    Story on the 1911?
  8. Replies
    33
    Views
    7,388

    Yup, that's the new box.

    Yup, that's the new box.
  9. Replies
    329
    Views
    26,703

    Chauvin is requesting a new trial...

    Chauvin is requesting a new trial. I doubt that the outcome would be much different, but there it is.
  10. Replies
    373
    Views
    41,768

    PDP/PPQ Compact 15+2 Mags Available

    From Walther, $46 each. I don't know if this is needed or a fair deal, just got the email because I'm on Walther's list.
  11. Replies
    14
    Views
    436

    I searched and came up empty. Some torque...

    I searched and came up empty. Some torque wrenches were mentioned but I didn’t see anything addressing accuracy at the low end of measurement.
  12. Replies
    14
    Views
    436

    Torque Wrench Recommendations?

    I have one of my PX4 slides in at LTT being machined for a red dot. I emailed them last night to ask about torque specs and got a reply of 10 inch-pounds. I’ve looked online and found some torque...
  13. Thread: Ammo deals!

    by revchuck38
    Replies
    1,687
    Views
    336,025

    Sticky: .45 AE Hardball

    Here, though it's getting pricier.

    ETA: Federal also shows lots of hunting 12 gauge 00 and slug ammo, with no limit on the 2-3/4" 00. No Flite Control stuff, though. They do show the new "X2"...
  14. Replies
    5
    Views
    551

    Thanks, Tom!

    Thanks, Tom!
  15. Replies
    5
    Views
    551

    Parrot Drill Scoring?

    On the zero circles, what counts as a valid hit?
  16. My copy of Lyman's Pistol and Revolver Handbook...

    My copy of Lyman's Pistol and Revolver Handbook (copyright '78) shows 4.1 grains of Bullseye as a max standard pressure load for #358495, which is a plain base wadcutter. You can blow the skirt off...
  17. The following assumes you're going to use .357...

    The following assumes you're going to use .357 Magnum brass. I'd go with either Unique or CFE-Pistol since they're about the same burn rate and slower than 231. Hodgdon shows 6.6 grains as max for...
  18. Replies
    23
    Views
    758

    The slide stop vs. slide release discussion has...

    The slide stop vs. slide release discussion has been going on for at least a century. I’m in the “whatever works for you” category. I use the slide release, but my 1911s are well broken in.
  19. Replies
    27
    Views
    1,147

    This is my plan when I get my PX4 slide back from...

    This is my plan when I get my PX4 slide back from Langdon.
  20. Thread: Ammo deals!

    by revchuck38
    Replies
    1,687
    Views
    336,025

    Sticky: They have several .460 and .500 loads available,...

    They have several .460 and .500 loads available, plus .41 Magnum. :)

    No .38 Special or .357 Magnum defensive ammo, though.
  21. Replies
    79
    Views
    4,901

    About 5 grains of Unique should do it. Something...

    About 5 grains of Unique should do it. Something cleaner-burning would be nice if you have any.
  22. Thread: 503s Agan

    by revchuck38
    Replies
    2
    Views
    208

    503s Agan

    Started about 0630 central, Windows 10 and Chrome with latest updates, cleared up about 0640.
  23. Replies
    19
    Views
    584

    After seeing this...

    After seeing this, I'm wondering how much I'd have to file down the front sight to make it work with my 681...
  24. Replies
    19
    Views
    584

    +1 on both paragraphs.

    +1 on both paragraphs.
  25. Thread: Ammo deals!

    by revchuck38
    Replies
    1,687
    Views
    336,025

    Sticky: Considering that they were charging about $100...

    Considering that they were charging about $100 for shipping about a month ago, that's not too bad.
Results 1 to 25 of 300
Page 1 of 12 1 2 3 4