Search:

I don't know when Glock made these changes, but they did update their 10 round mags, at least the ones for the 19. The new magazines are marked 2274-02 on the rear of the body. The new magazine...

CHPWS can mill a Glock MOS cut in the rear dovetail section of your slide, and cut a new rear sight dovetail in front of the MOS cut. You're probably better off getting the AOS cut from Agency Arms,...

could you please change my username to "fig_je" or "figje" if underscores arent allowed in usernames.

If the user's page (/u/username) says the account was deleted, then the user deleted the account his/herself. Otherwise it would say the user was suspended (banned).

I've had about a dozen of the 10 round G19 magazines over the years since they came out. I haven't had any issues with them. I've ran a variety of the premium self defense JHPs with them (Federal...

There's several ways around this, if you cannot legally acquire standard capacity magazines in your state.

Easiest ways are to either buy blocked standard capacity mags from somewhere like...

I ended up getting the pin out with a 1.8mm punch and installed a set of carry levers. Lining up the holes on both sides of the carry levers was a challenge, so I lined them up and steadied them by...

I started to drift the pin from the bottom of the slide, and got it to budge a bit more on the other side. I've also been using imperial sized punches since I couldn't find the true dimensions of the...

Hi everyone,

I just purchased a Beretta PX4 storm, and am trying to convert the safety levers to decock only. However, the roll pin that they have in there is so tight that it's broken several...

I've found that carefully fitting the current generation standard capacity 9mm Glock followers (labeled 9mm6) into 10 round Glock magazines tends to clear up any kind of reliability problems with...

I put a box of 147gr HST and a mix of 100 rounds of LAX and Perfecta 115gr through two of the magazines with no problems. Loading the last round in each mag was worse than loading OEM 10 round Glock...

Interesting, I've been waiting for something like this for awhile. I've been using OEM Glock 10 round magazines slightly modified to accept the 9mm6 follower in my G19, because the 2183 followers and...

5'10" @ 185 lbs

I found that while I can accommodate both G19 and G17 length holsters AIWB, I strongly prefer the G19 length. The G17 length holsters tend to dig into my thighs or the crease of my...

I installed the apex extractor on a G19 I acquired last August, it didn't require any fitting. Since you already installed the 30274 ejector, I would just throw in both the HRED and Apex extractor...

I'm a big fan of the Dawson adjustable sights. I'm a stickler for getting a precise zero and I love the tight dimensions of the sight blade/notch.

I think the best way you're going to find out if it's going to be comfortable to carry a longer pistol AIWB is to try some kind of IWB holster for your 17 in the AIWB position and see if there's any...

Hello mods,

Could you change my username to just "ueber"?

As a broke college student, I only have one P2000. I don't have the funds to buy one or two more copies of the same pistol, so I just make sure to have at least 2 spares of each of the common wear...

I wonder if the sharpness depends on the batch or model of HDs, I've never had any kind of problem with the edges of the HD sights on my HK pistols. I think that using a file to hit the edges would...

The 4.1 LEM kit does work on the P2000, but since you can't use medium-weight TRS that is P30 specific, you have to use the light or heavy TRS for the P2000 series. I was advised to use the heavy TRS...

P2000 9mm LEM, my one and only (sadly).

How much did you have to file for the front sight to fit?

To clarify, you're pulling the trigger in DA mode all the way through its full range of motion, and nothing happens. But once you let go of the trigger the hammer drops? If so, it sounds like...

Just about every firearm in existence is going to be loud enough to cause cumulative hearing damage without proper ear protection. I think it's kind of silly to get rid of some firearms just because...

Is it just me or does the picture of the rear sight that Dawson has on their product page not match bofe954's pictures?