No, just the standard mil-spec(ish) single stage with whatever nickel coating they use.
Type: Posts; User: Sero Sed Serio
No, just the standard mil-spec(ish) single stage with whatever nickel coating they use.
I wanted to share my recent experience with Sionics because I was blown away by their responsiveness to a minor issue with a rifle:
A few months ago I bought a Sionics 16" rifle direct from the...
Not BehindBlueI's, but I have heard of this exact scenario. A Pima County (Tucson) AZ Deputy told me about an out-of-battery failure to fire during an upright grapple where the suspect grabbed his...
Has anyone noticed an increase in issues with Magtech ammo? It has been my go-to for a few years now because it is readily available, competitively priced, and has always been drama-free.
Over...
I’m on about month 7 of my wait for my Mask, but once I get it I’ll have a very similar setup.
117307
I was lucky enough to stumble across one of the special run all-stainless P229s new/old stock a couple of years ago. It was manufactured in 04-06 based on the serial number, and the model...
117261
It’s a very bespoke desire, but an all-steel 6-shot .32 H&R humpback that I can thumb the hammer while reholstering, UC sights, and a DLC black finish would be my ultimate J frame…
Nothing on gun.deals or GunBroker, and I’ve been checking pretty regularly. I shot yesterday at a fairly large range/dealer that might be likely to get something like this early on (they got a...
Picked up my 432 from the FFL today (it was, in fact, a 432), then got home in time to get my shipment of Lost River ammo.
The tritium sight is bright, and the green ring around it glows extremely...
Hopefully the wait isn’t too long! I’ve been happy with KY Gun Co in the past, and yesterday I placed my order at 9:20, got a notification that it had shipped at 1:36.
Thank you! There was...
KY Gun Co. has the 432 in stock at non-gouging prices plus cheap shipping and no CC fees (or at least what I hope is the 432–it says 632, but the description and model number are all for the 432).
...
I also find a longer grip to cause more printing issues than a thicker grip, whether AIWB or behind the hip. The slightly chonkier G26 makes a slightly bigger bulge, but I don’t get the corner of...
Law schools use the term “eggshell skull plaintiff” to teach this concept, or “you take the victim as you find them.” Much as a drunk driver cannot argue that the other driver would have survived if...
To be fair I’ve never been downtown, just off the highway. Definitely not Lordsburg. I used to travel to Bowie a lot for work, but never crossed the state line.
Saw one of these in the wild at C2 Tactical in Tempe, a pretty good-sized local range. Was confused because I just assumed it was one of the Gunsite limited runs, but this confirms it wasn’t.
I...
They do outstanding work. Impact was one of the few companies that would take on a direct milling project for a SIG P-series, and they did an amazing job. Scott is my first choice for any direct...
In fairness, I’ve been to Willcox, and I’d do what I had to do to get out of there, too
115266
Necropost, but I want to reemphasize the interest for a G42 SCD.
I wonder if the fact that multiple major agencies (LAPD, Dallas, Vegas, CT State Police, plus FLETC which is not mentioned here, and the smaller agencies) prohibit the SERPA could start to approach...
I found the DAK trigger to be very useable—like a light DA, vs. LEM, which I thought combined all the worst qualities of a Glock trigger with all the worst qualities of a DA trigger. I also found...
Add me to the list for a pair of 432s, maybe a trio. One of my next purchases was going to be an LCR .327, but it wasn’t quite right: a little larger, no tritium front, rubber stocks that need to be...
I work near the AZ Capitol, which is patrolled by Arizona DPS instead of Phoenix Police (Until the mid-2000s Capitol Police was its own agency that got absorbed into AZ DPS). Walking into work this...
I've been very happy with the Dawson Chargers that I have on my P2000. I much prefer a .125 front, so Trijicon/Meprolight/whoever else does P2000 sights wasn't an option. I was able to choose my...
Cleaned the G19 last night, and found another ring stuck between the magazine release and the frame inside the mag well. It was wedged horizontally on the right side of the mag well in a small gap...