Any chance you can provide a photo or measurement of this? I had a failure to eject with Champion 115 in my MP5 clone and couldn't figure out why considering it eats just about every other quality...
Type: Posts; User: einherjarvalk
Any chance you can provide a photo or measurement of this? I had a failure to eject with Champion 115 in my MP5 clone and couldn't figure out why considering it eats just about every other quality...
I think it may actually be counterproductive to wear gloves all the time when leaving the house due to the risk of cross-contamination. What good does it do you to wear gloves to protect yourself...
"Works for me" needs to be replaced with "works for my purposes." Getting people to be honest about why they own what they own would immediately clear up a huge amount of derp on the internet about...
The only issue I've seen with ACRO mounting failures was an MOS plate dying on him with the factory B&T mount and screws. Happened to Steve Fisher and sort of happened to me too. It wasn't the ACRO...
Everyone go home, we're done here.
45497
Is it at all possible to determine the model of a Malkoff head from visual inspection? I've got an Arisaka 600 I bought used and have zero clue what head it currently has on.
If you're willing to take a gamble on a used AK, keep an eye on GT Distributors Austin's Gunbroker account.
Apparently some PD in west Texas pulled over a truck for a traffic stop and found a few...
I'll say what I've been saying elsewhere about this - believe it when they're on shelves and not a day before then. Remember that HK announced the HK243 (civilian G36) years ago, and those have never...
Is there an ETA for the course block scheduling yet?
Has anyone figured out the dimensions of the Ameriglo Bold sights that Glock is putting on the 43X/48? Ameriglo's website offers exactly zero help (in fact, there's not a single mention of the 48 to...
Capitol Armory also sells Mega-made lowers; I think the rollmark is much nicer, if a little too close for comfort to a well-known airsoft company's logo. Also significantly cheaper than JSE's lowers....
Why not? I'm in.
My initial goal in asking this was less about compensator performance and more about whether or not the ALS mechanism will hang up on a non-profiled compensator and a Gen 5 slide.
That said, right...
I picked up a G45 last week with the intent of turning it into a full-frame clone of my current G19.4 MOS - threaded barrel, Agency 417 single port comp, RDS, X300U. While looking at less expensive...
Has anyone had a chance to try both finishes on these side-by-side? With Robar scaling back their NP3 coatings, I'm trying to decide whether I should jump on one in NP3 now or if the Duralube finish...
My experience with the USP has been that the USP has a shorter reset than the P30 regardless of the trigger model. However, GrayGuns recently released a drop-in part that advertises a reduced reset...
That's some solid shooting. My Blacklist G19.4 barrel is threaded and currently has a comp mounted up on it, which is why I was considering a swap. Otherwise, I'd likely just leave it be as my G19.5...
I'm starting to give some thought to shuffling around some projects, selling my "backup" G19.5, and picking up a G45 MOS for later use with an ACRO. One thing I'm curious about that I can't recall...
I wasn't aware we were allowed to post porn here. :rolleyes:
Who made those 3d-printed stands? Those look super slick.
Thanks, I went ahead and gave my ACRO crossbolt a tiny bit of VC3 to be extra safe.
Are you guys using threadlocker of any sort on the crossbolt to mount the ACRO to the slide or adapter plate? I took my ACRO off my MOS slide after just over 1,000 rounds to make sure my adapter...
Follow up after a couple of range sessions:
Functionally, the gun now runs properly and is very easy to shoot at 25 yards once zeroed. The offset recoil lug does not appear to be negatively...
Would you mind sharing a photo of the bottom of your carrier from your personal Z-5, taken as squared up as possible from above? I'm trying to figure out if having a perfectly straight carrier is...
For what it's worth, the vast majority of Zenith owners don't ever seem to have any issues, same as PTR owners. However, I try to be extremely attentive to detail (that, or my anxiety forces me to...
I got an e-mail back from Rob at Zenith this morning. He sent me a number of photos of BCGs from both MKE and HK guns for comparison. All of the MKE carriers had a slight angle to the ejection side...