Compact and Lightweight, Scout-like, .308 Bolt Gun

Hello y’all!

I’m looking for a rifle like the title reads.

I would like:
- to put a 1-5 or 6x vs a 1-8x or possibly a 2.5-10 scope on it.
- I would like to use 5-20 round mags, with extra points if it takes AR pattern mags
- be able to use it as a personal defense weapon in states like CA, on overlanding trips
- Use it for medium to large game out to 300 yards or so.
- Be able to shoot reduced IPSC silhouette steel (12x24”) out to 500 yards

The Ruger an Steyr Scouts are very intriguing but force you to mount a scope far forward, which I don’t want to do. And I would be willing to give up iron sights for a more traditional scope mounting system.

There is the Mossberg MVP Scout, which has a longer rail that comes all the way back and takes AR10 mags but I’m concerned about quality and action.

I like what’s going on here with this Tikka (video below), but the 10 round mags are $90 each, and I’d have to get some good gunsmith to cut down the barrel. But if pressed I'd go this type of route at this point.

https://www.youtube.com/watch?v=-x7N8hLI2yM

Any thoughts would be greatly appreciated.

https://pistol-forum.com/showthread....fle-circa-2016

T3x for sale

http://www.apppicker.com/applists/24...for-craigslist

You can cut down the barrel yourself.

It's a trivial task if you have some basic files and buy the crowning tool from Brownells.

I own a couple bolt rifles in 308, one is a 20" and the other a 26", heavy profile barrels, and without muzzle brakes. The 26" has shot 8" diameter circles at 550 yards, and the 20" has shot steel at 550, 844, and 1000 yards using handloads with a mildly loaded 155 Berger Hybrid. Targets varied between 8 and 16" square.

Inside of 600, a reduced torso target would not be difficult, as long as you can read the wind. 1MPH of full value wind at 600 yards will push a 175 Sierra Matchking 3 inches. 5MPH is around 15 inches which makes things more interesting. 147 grain ball is similar but may not be as inherently accurate. For reference, 6.5 Creedmoor is around 10" with the same parameters which is why it is gaining in popularity so fast. Sales of 308 rifles are way down because of this.

If you own an AR or a 223 bolt gun, a 77 SMK has similar ballistics so you can practice the wind reads with one of them.

I would prefer a 2.5-10x scope for this application. This morning I was shooting a full size silhouette at 545 yards and snapped a pic. It should give you an idea of the sight picture, looking through a 2.5-10x Leupold
Attachment 42595

As for magazines, I prefer anything that takes the AICS pattern magazines. There are several manufacturers that make bottom metal which accept this magazine, and Magpul makes reasonably priced magazines for it. Currently the only production rifles that I know of that accept this magazine are from Remington, Bergera, and Accuracy International, but some rifles can be retrofitted to accept the magazines, and most of the aftermarket stocks with magazine style button metal will accept them.

Ruger makes the American that takes AICS mags. The polymer AICS mags by MDT and Magpul are 30 some bucks.

https://ruger.com/products/americanR...ets/26974.html

W/ Magpul stock:
https://ruger.com/products/americanR...ets/26993.html

Quote:

---

Originally Posted by David S.

https://pistol-forum.com/showthread....fle-circa-2016

---

Beat me to it.


Okie John

Quote:

---

Originally Posted by DacoRoman

Hello y’all!
(Clippage)
The Ruger an Steyr Scouts are very intriguing but force you to mount a scope far forward, which I don’t want to do. And I would be willing to give up iron sights for a more traditional scope mounting system.
(More clippage)
Any thoughts would be greatly appreciated.

---

Either the Steyr or Ruger GSR will allow you to mount a traditional scope. The Ruger requires that you remove the rear aperture sight to use the included Ruger rings but it’s only held on by one screw. The Steyr is considered the ideal but I like my GSR and it shoots sub inch 100 yard groups if I do my part.

I'm seriously tempted by the Savage 110 scout, not the 11. Both guns use a standard pattern of holes for mounting scope rails and iron sights so if you prefer you could replace the forward rail and rear sight with a conventional rail and sights from a Hog Hunter model. Or maybe you could convert a Hog Hunter to take the 110 scout mags. I would be surprised if that was a difficult swap.

There's is an Australian company making 9-round mags for the .308 BLR but I don't know if they can be had in the US. And the mags are expensive AF.

I would pay absurd amounts of money for a 5.56 lever action that took AR15 mags. Or grab a Remington 7615 Police if they were reliable enough for their intended role.

I would research this and the several similar products to see how well they actually work:

https://www.redsnake-tactical.com/

Tikka is the answer you seek.

The hard work and research has already been done.

In Spades.


http://i.imgur.com/WWCXC3c.jpg

http://i.imgur.com/C4wmqRU.jpg

http://i.imgur.com/UXUaFN7.jpg

http://i.imgur.com/yHJVfCu.jpg

Quote:

---

Originally Posted by DacoRoman

The Ruger an Steyr Scouts are very intriguing but force you to mount a scope far forward, which I don’t want to do. And I would be willing to give up iron sights for a more traditional scope mounting system.

---

As has been pointed out, neither rifle forces you to do anything of the sort. I am less familiar with the Steyr (too expensive for me, and no left hand version), but the Ruger comes with traditional scope rings in the box. (If you want to retain BUIS, that's when things get trickier with the Ruger.) Now if you want to use a forward mounted optic, these two rifles are the most common ones that enable it in stock form, which is why you tend to see these with those sort of optics on them. But they work just as well with traditional scopes, too.

Quote:

---

Originally Posted by SecondsCount

As for magazines, I prefer anything that takes the AICS pattern magazines. There are several manufacturers that make bottom metal which accept this magazine, and Magpul makes reasonably priced magazines for it. Currently the only production rifles that I know of that accept this magazine are from Remington, Bergera, and Accuracy International

---

The Ruger Scout magazines are AICS pattern. Several folks have reported success using Magpul magazines.

Quote:

---

Originally Posted by Bigghoss

There's is an Australian company making 9-round mags for the .308 BLR but I don't know if they can be had in the US. And the mags are expensive AF.

---

If it's the same company that makes 10 round T3 magazines, that guy will ship globally. The magazines are, as you said, extremely expensive though.

Over on the scout rifle forum, there has been some discussion on the difficulties of making a bolt action rifle run properly using a magazine meant for a semi-automatic rifle. Not sure how much of that was justification after the fact when the Ruger Scout was released and it did not use AR-10 magazines, though?

Quote:

---

Originally Posted by That Guy

If it's the same company that makes 10 round T3 magazines, that guy will ship globally. The magazines are, as you said, extremely expensive though.

---

https://www.luckythirteen.com.au/pro...re-fire-range/

As mentioned, the Ruger GSR gives you the option of either forward mounting or traditional mounting for an optic. The Ruger rings require removing the rear sight but you can put on an XS mount that offers both conventional scope placement as well as a back-up ghost ring.

I like mine a lot although I sometimes wish I had opted for the 18 inch barrel. Mine also won't consistently pop primers on 7.62x51. The polymer mags are better in every way than the gargantuan and rough feeding factory metal mags.

I own a .308 caliber Steyr Scout and currently have a Leupold Mark 4 1.5 - 5X20mm MR/T scope in Talley rings mounted in the traditional, over the action position. It works quite well. And so does a Leupold FX-II Scout IER 2.5x28mm scope mounted in the forward position.

Quote:

---

Originally Posted by DacoRoman

Hello y’all!

I’m looking for a rifle like the title reads.

I would like:
- to put a 1-5 or 6x vs a 1-8x or possibly a 2.5-10 scope on it.
- I would like to use 5-20 round mags, with extra points if it takes AR pattern mags
- be able to use it as a personal defense weapon in states like CA, on overlanding trips
- Use it for medium to large game out to 300 yards or so.
- Be able to shoot reduced IPSC silhouette steel (12x24”) out to 500 yards

Any thoughts would be greatly appreciated.

---

I read the Practical Rifle circa 2016 thread forwards and backwards while making a purchase decision with similar criteria that you laid out. The only other thing on my list, and it was a "must have", is a factory threaded barrel for use with a suppressor. I ended up with the 20" Tikka T3x CTR in 308 (JRTXC316).

It does everything you're looking for out of the box without modification, but is a bit heavier than the Lite Compact. The Lite Compact is stated at 6.6lbs and the CTR is listed at 7.5lbs. That said, it has 10rd steel mags and comes with an optic rail. The rail is a must have, so those couple ounces will need to be added to the Lite Compact base weight, making the difference even smaller. The 10rd mags are something I can appreciate as well.

My CTR with Vortex Razor Gen II-E 1-6, Warne Maxima rings, Rhodesian Sling, stock pack, and SilencerCo Omega suppressor comes it at exactly 11lbs unloaded on our digital bathroom scale. It's no mountain gun, but it's absolutely perfect for what I need. I am, however, planning to sell the 21.5 ounce Razor 1-6 and replace it with something lighter.

https://live.staticflickr.com/4835/4...9a382b67_c.jpg

https://live.staticflickr.com/7854/4...9d822290_c.jpg

Scope rings for Tikkas:

https://pistol-forum.com/showthread....l=1#post627816

Quote:

---

Originally Posted by SecondsCount

I own a couple bolt rifles in 308, one is a 20" and the other a 26", heavy profile barrels, and without muzzle brakes. The 26" has shot 8" diameter circles at 550 yards, and the 20" has shot steel at 550, 844, and 1000 yards using handloads with a mildly loaded 155 Berger Hybrid. Targets varied between 8 and 16" square.

Inside of 600, a reduced torso target would not be difficult, as long as you can read the wind. 1MPH of full value wind at 600 yards will push a 175 Sierra Matchking 3 inches. 5MPH is around 15 inches which makes things more interesting. 147 grain ball is similar but may not be as inherently accurate. For reference, 6.5 Creedmoor is around 10" with the same parameters which is why it is gaining in popularity so fast. Sales of 308 rifles are way down because of this.

If you own an AR or a 223 bolt gun, a 77 SMK has similar ballistics so you can practice the wind reads with one of them.

I would prefer a 2.5-10x scope for this application. This morning I was shooting a full size silhouette at 545 yards and snapped a pic. It should give you an idea of the sight picture, looking through a 2.5-10x Leupold
Attachment 42595

As for magazines, I prefer anything that takes the AICS pattern magazines. There are several manufacturers that make bottom metal which accept this magazine, and Magpul makes reasonably priced magazines for it. Currently the only production rifles that I know of that accept this magazine are from Remington, Bergera, and Accuracy International, but some rifles can be retrofitted to accept the magazines, and most of the aftermarket stocks with magazine style button metal will accept them.

---

Thanks for the information rich response, I greatly appreciate it.

Regarding shooting at range, what you wrote validates some of my own, but much more limited, experience regarding shooting at distance. My only reference point is from a John McPhee "heavy carbine" class where we shot from 100-600 yards.

I ran a 16" AR platform with a Burris XTRII 1-5X, with Magtech/CBC 77grain Mk262 clones. Reticle hold-overs where used exclusively. I used the scope in 5X exclusively, and on 12x24" targets I was hitting at 450 yards about 70% of the time at least. Probably 90% at 400 yards.

The 500 yard target was in shade in the tree line and I couldn't see the target well enough, including my bullet splashes, to get any hits on it. The 600 yard target was also a no go; it was exposed in sunlight, but I wasn't able to hit it. Two students let me shoot their AR's, one with a Leupold 1-8x, and another with a NF SHV 4-14X I think it was. I was able to hit the shaded 500 yard target repeatedly using 8x and 10x. I didn't have a chance to have a go at the 600 yard target with their guns unfortunately. Wind was pretty low the whole weekend, maybe 1-2mphs, and not much over 5mph I don't think.

But yeah, my conclusion was that for 500 yards I need at least 8X, and preferably 10X, especially if the target is in some kind of shade.

Quote:

---

Originally Posted by whomever

Ruger makes the American that takes AICS mags. The polymer AICS mags by MDT and Magpul are 30 some bucks.

https://ruger.com/products/americanR...ets/26974.html

W/ Magpul stock:
https://ruger.com/products/americanR...ets/26993.html

---

Dang..those are pretty nice! And great news about the mags. I'll certainly be considering this Ruger.

Quote:

---

Originally Posted by Rick R

Either the Steyr or Ruger GSR will allow you to mount a traditional scope. The Ruger requires that you remove the rear aperture sight to use the included Ruger rings but it’s only held on by one screw. The Steyr is considered the ideal but I like my GSR and it shoots sub inch 100 yard groups if I do my part.

---

Ahh, thanks for the clarification. This may change things a bit. It's good, more choices to consider.

Quote:

---

Originally Posted by Rick R

Either the Steyr or Ruger GSR will allow you to mount a traditional scope. The Ruger requires that you remove the rear aperture sight to use the included Ruger rings but it’s only held on by one screw. The Steyr is considered the ideal but I like my GSR and it shoots sub inch 100 yard groups if I do my part.

---

The Steyr does allow mounting a traditional scope but the mounting set up / spacing is less than optimal both in terms of eye relief and bolt knob clearance.

Quote:

---

Originally Posted by Bigghoss

I'm seriously tempted by the Savage 110 scout, not the 11. Both guns use a standard pattern of holes for mounting scope rails and iron sights so if you prefer you could replace the forward rail and rear sight with a conventional rail and sights from a Hog Hunter model. Or maybe you could convert a Hog Hunter to take the 110 scout mags. I would be surprised if that was a difficult swap.

There's is an Australian company making 9-round mags for the .308 BLR but I don't know if they can be had in the US. And the mags are expensive AF.

I would pay absurd amounts of money for a 5.56 lever action that took AR15 mags. Or grab a Remington 7615 Police if they were reliable enough for their intended role.

---

Wow, I didn't even realize Savage made a scout...but I'm a babe in the woods when it comes to bolt, and lever guns. Thanks for the Savage suggestions, will be checking them out.

But speaking of lever guns, that BLR is an absolute beast..a beautiful beast. It is almost too nice. I am used to Glocks and AR's which I slap around as needed ...that BLR is a work of art that I'd be afraid to manhandle. Actually, that stainless takedown looks pretty tough...I don't know, I could see that BLR being a total impulse buy if I see it in a store. It looks like one can get a scope base for it too. Too bad about no higher cap. mags that are easily obtained though.

I'm surprised that there aren't more modern lever guns that use mags though.

Quote:

---

Originally Posted by OlongJohnson

I would research this and the several similar products to see how well they actually work:

https://www.redsnake-tactical.com/

---

Intriguing for sure, thank you very much for the lead!

Quote:

---

Originally Posted by Lost River

Tikka is the answer you seek.

The hard work and research has already been done.

In Spades.


http://i.imgur.com/WWCXC3c.jpg

http://i.imgur.com/C4wmqRU.jpg

http://i.imgur.com/UXUaFN7.jpg

http://i.imgur.com/yHJVfCu.jpg

---

Man, that is super legit! Thank you for your hard work!

I tell you something...that Tikka, it may be hard to beat.

Quote:

---

Originally Posted by That Guy

As has been pointed out, neither rifle forces you to do anything of the sort. I am less familiar with the Steyr (too expensive for me, and no left hand version), but the Ruger comes with traditional scope rings in the box. (If you want to retain BUIS, that's when things get trickier with the Ruger.) Now if you want to use a forward mounted optic, these two rifles are the most common ones that enable it in stock form, which is why you tend to see these with those sort of optics on them. But they work just as well with traditional scopes, too.



The Ruger Scout magazines are AICS pattern. Several folks have reported success using Magpul magazines.



If it's the same company that makes 10 round T3 magazines, that guy will ship globally. The magazines are, as you said, extremely expensive though.

Over on the scout rifle forum, there has been some discussion on the difficulties of making a bolt action rifle run properly using a magazine meant for a semi-automatic rifle. Not sure how much of that was justification after the fact when the Ruger Scout was released and it did not use AR-10 magazines, though?

---

Excellent info, thanks.

Quote:

---

Originally Posted by Bigghoss

https://www.luckythirteen.com.au/pro...re-fire-range/

---

they look quite good! but I see no prices advertised...I may email them at some point

Quote:

---

Originally Posted by MK11

As mentioned, the Ruger GSR gives you the option of either forward mounting or traditional mounting for an optic. The Ruger rings require removing the rear sight but you can put on an XS mount that offers both conventional scope placement as well as a back-up ghost ring.

I like mine a lot although I sometimes wish I had opted for the 18 inch barrel. Mine also won't consistently pop primers on 7.62x51. The polymer mags are better in every way than the gargantuan and rough feeding factory metal mags.

---

That's some good info on the GSR thank you. That XS sight system seems like a no brainer. What makes you miss an 18" barrel if you don't mind me asking?

Is there a fix for the light primer strikes on the 7.62x51?

Quote:

---

Originally Posted by 1911Nut

I own a .308 caliber Steyr Scout and currently have a Leupold Mark 4 1.5 - 5X20mm MR/T scope in Talley rings mounted in the traditional, over the action position. It works quite well. And so does a Leupold FX-II Scout IER 2.5x28mm scope mounted in the forward position.

---

Well there you go. Thanks for the clarification. I'd love to see a pic of your set up if it isn't too inconvenient.

Quote:

---

Originally Posted by StraitR

I read the Practical Rifle circa 2016 thread forwards and backwards while making a purchase decision with similar criteria that you laid out. The only other thing on my list, and it was a "must have", is a factory threaded barrel for use with a suppressor. I ended up with the 20" Tikka T3x CTR in 308 (JRTXC316).

It does everything you're looking for out of the box without modification, but is a bit heavier than the Lite Compact. The Lite Compact is stated at 6.6lbs and the CTR is listed at 7.5lbs. That said, it has 10rd steel mags and comes with an optic rail. The rail is a must have, so those couple ounces will need to be added to the Lite Compact base weight, making the difference even smaller. The 10rd mags are something I can appreciate as well.

My CTR with Vortex Razor Gen II-E 1-6, Warne Maxima rings, Rhodesian Sling, stock pack, and SilencerCo Omega suppressor comes it at exactly 11lbs unloaded on our digital bathroom scale. It's no mountain gun, but it's absolutely perfect for what I need. I am, however, planning to sell the 21.5 ounce Razor 1-6 and replace it with something lighter.

https://live.staticflickr.com/4835/4...9a382b67_c.jpg

https://live.staticflickr.com/7854/4...9d822290_c.jpg

---

That's a sweet set up for sure. 7.5lbs isn't too bad. The more I think about it, since it will be carried in the truck, a 20" barrel may be just fine. I was thinking of getting a barrel cut down to 16.5", which would also save weight. I also do have an AAC suppressor that I was planning on putting on it at times, hence the other reason to get a bbl cut down. Well, I don't know, that bears further consideration. I could of course just see how it works for me with the 20" bbl for awhile.

Many thanks for the responses everyone.

I am leaning Tikka, but there are some other really good options too. I'm planning on buying at Christmas so I have some time to deliberate.

For a scope I'm thinking a NF 1-8x, the "budget" one, not the ATACR..or maybe the ATACR, depending on what I'll end up wanting to consign or trade, or look for a FFP 2.5-10X of some sort. Any good suggestions for a FFP 2.5-10x?

Quote:

---

Originally Posted by DacoRoman

Many thanks for the responses everyone.

I am leaning Tikka, but there are some other really good options too. I'm planning on buying at Christmas so I have some time to deliberate.

For a scope I'm thinking a NF 1-8x, the "budget" one, not the ATACR..or maybe the ATACR, depending on what I'll end up wanting to consign or trade, or look for a FFP 2.5-10X of some sort. Any good suggestions for a FFP 2.5-10x?

---

Nothing ruins the handling of a lightweight rifle concept more than a big fucking heavy scope that is designed for big heavy marksman rifles. If you're to the point of cutting off 3.5" of barrel to save weight, then it makes zero sense to buy an optic with significant weight.

Unless you're going to obsess over Tacti-timmy details that aren't critical (or outright pointless, even) for the stated application and ruin the entire concept of the rifle, I'd seriously look at this: New Ultralight 2.5-10x32 Scope from SWFA. Some other options here, but I think that's a hard option to beat.

It's 9oz. That's about 1/3rd to 1/2 the weight of common tactical/precision oriented scopes, such as the Nightforce NXS 2.5-10x42 "compact" rifle scope. IMO, respectfully, if you're going for a lightweight rifle concept for inside 300 yards on game, buy a lightweight scope that is suitable for game inside of 300 yards; If you want a precision rifle with a scope built for such, then buy a precision rifle and be honest/consistent what you're trying to build. As for the LPVO option, unless you're room clearing or doing some sort of super fast target acquisition within 15 yards, you don't need a LPVO. It doesn't make sense to put those on a bolt action hunting rifle regardless of them being all the heat these days to put on carbines for shooting terries.

Quote:

---

Originally Posted by DacoRoman

they look quite good! but I see no prices advertised...I may email them at some point

---

The Australian gun channel I saw them on said they ran something like $114AUD which converts to $95 American. If you can even get them here.

After having lots and lots of different bolt action rifles over the years, I’d really hate to see anyone end up with a factory action that wasn’t a Tikka. CTR has a really great barrel. Tikka factory trigger is money. But factory mags are not as reliable as AICS pattern. Plus, stock doesn’t have adjustability.

A Tikka barreled action dropped into a KRG Bravo chassis gets you a fine rifle. Upgrade to AICS compatible bottom metal. And you get the adjustability. I don’t think people put enough emphasis on setting the rifle up for proper fit.

Regarding barrel length and caliber: I don’t know what drives you towards 308 but if you haven’t you might take a look at 6.5 Creedmoor. Factory Hornady ammo is cheap, plentiful, and sinfully consistent. I had this caliber in a 16.5” barrel, it’ll make hits on smaller targets at longer distances than your requirements easily.


Sent from my iPhone using Tapatalk

Quote:

---

Originally Posted by DacoRoman

Well there you go. Thanks for the clarification. I'd love to see a pic of your set up if it isn't too inconvenient.

---

Here are a couple of photos of the Steyr Scout with the Leupold scope attached over the action, as requested.

Attachment 42666Attachment 42667

Quote:

---

Originally Posted by DacoRoman

But speaking of lever guns, that BLR is an absolute beast..a beautiful beast. It is almost too nice. I am used to Glocks and AR's which I slap around as needed ...that BLR is a work of art that I'd be afraid to manhandle. Actually, that stainless takedown looks pretty tough...I don't know, I could see that BLR being a total impulse buy if I see it in a store. It looks like one can get a scope base for it too. Too bad about no higher cap. mags that are easily obtained though.

I'm surprised that there aren't more modern lever guns that use mags though.

---

There is also the Henry Long Ranger. Similar to the BLR, not available in as many chamberings, has a less refined look to it but still looks good.

Quote:

---

Originally Posted by DacoRoman

That's some good info on the GSR thank you. That XS sight system seems like a no brainer. What makes you miss an 18" barrel if you don't mind me asking?

Is there a fix for the light primer strikes on the 7.62x51?

---

Sorry for the late response.

On the 18 barrel, personal preference. 16 inch is about the limit you can take a .308 and still be a .308. The 16 is also LOUD and I’ve been shooting ARs with brakes my whole adult life.

I’ve read that the GSR might not be the best rendition of a scout rifle but it’s a nice update on the Enfield Jungle Carbine. Being in a ban state, that appeals.

Quote:

---

Originally Posted by DacoRoman

But speaking of lever guns, that BLR is an absolute beast..a beautiful beast. ...that BLR is a work of art that I'd be afraid to manhandle. Actually, that stainless takedown looks pretty tough...I don't know, I could see that BLR being a total impulse buy if I see it in a store. It looks like one can get a scope base for it too. Too bad about no higher cap. mags that are easily obtained though.

I'm surprised that there aren't more modern lever guns that use mags though.

---

I've read discussion that there's a plastic gear in the BLR action that can strip out if the lever is run too hard, too much. Makes it less attractive for serious use.

Someone mentioned the Henry. I recall mentions of less than perfect reliability/durability.

I'd love to see someone figure out a lever-action receiver and bolt system that would work with AR uppers and mags in a way that made actual sense.

Quote:

---

Originally Posted by DacoRoman

they look quite good! but I see no prices advertised...I may email them at some point

---

I emailed them through their web site. Aussie export laws are apparently fairly rigorous, and they can't currently export to U.S. I emailed a stateside contact who may be a good fit for taking on a project like that. Maybe in six months or a year something will come of it.

Quote:

---

Originally Posted by MK11

Sorry for the late response.

On the 18 barrel, personal preference. 16 inch is about the limit you can take a .308 and still be a .308. The 16 is also LOUD and I’ve been shooting ARs with brakes my whole adult life.

I’ve read that the GSR might not be the best rendition of a scout rifle but it’s a nice update on the Enfield Jungle Carbine. Being in a ban state, that appeals.

---

FWIW I have an early 16.5” Ruger Scout and the barrel is actually 17.25”. It’s like they got the specs settled and someone said “let’s add a threaded section for a flash suppressor or other ;) muzzle device!”. And then they added 3/4” but didn’t change the specs.

At least if you move to a place where a threaded barrel is prohibited, you can just cut the threads off and roll on.

Another, albeit price option:

https://www.eurooptic.com/Christense...-03001-00.aspx

Christensen Arms Modern Precision Rifle .308 Win 16" 1:10" Black 801-03001-00
SKU 801-03001-00-CA

Quote:

---

Specifications
Caliber: .308 Win.
Weight: 6.9 lbs.
Rifle Overall Length: 36.75" Extended
28" Folded
Action: Bolt
Trigger: Match-Grade "Flat" Trigger
Rifle Barrel Length: 16"
Rifle Barrel Twist: 1:10"
Barrel Thread Pitch 5/8"-24
Rifle Stock: Black Folding Stock with Locking Hinge and Magnelock Technology
Scope Mount: 20 MOA Picatinny Rail
Magazines Included: AICS-Compatible Detachable
Iron Sights No
Caliber or Gauge: .308 Win
Handedness Right Hand
Item Condition New
Product Type Rifles
UPC

---

Attachment 42689