PDA

View Full Version : martin_j001 reloading



martin_j001
06-18-2018, 04:58 AM
I had overlooked this section previously.

Reloading press used (list modifications if relevant)installed: Dillon 650, ceramic ball bearing/spring for smoother shell plate stops, ebay live primer chute catch can, and spent primer catch can
Caliber: 9mm
Bullet (Weight, Coating, Profile, Manufacturer): The Blue Bullets 125gr RN
Powder manufacturer, type and charge; volume, type (ball, stick, flake): was at 3.7-3.8gr, bumped up to 3.8-3.9gr just recently
Dies used: Dillon
Primers used: Winchester
Cartridge Overall Length (COAL): ~1.125
Chronograph data (if possible): chrono'd the 3.7-3.8gr load recently, and came out to a 132 power factor, with a standard deviation around 15fps for 10 rounds (so ~1060fps)
Goals intended with this load: This is my do everything load...I shoot it in matches, shoot it for practice/training, and use it in classes as well. While I could shoot "bunny farts" for competition and practice, I'd prefer the recoil impulse to feel not that extremely different from my carry ammo, which is currently 147gr HST or 124gr HST.
Results - accuracy, smokiness, clean burning, flash, temperature, smell, brass deformation, etc.: Seems accurate, at least as much as I can expect in my hands. A little smoky at times, can definitely smell it at times. Don't see any brass deformation.
Problems encountered and fixes applied: Early on when starting to load with Blue Bullets I did see some leading, but found it was 100% due to my own fault and crimping a touch too tight.
Anything of interest: Hope to chrono the 3.8-3.9gr soon, and will continue to run some more of it in practice to check for possible issues.

Duelist
06-19-2018, 04:24 AM
What powder are you using?

martin_j001
06-19-2018, 04:36 AM
What powder are you using?

There I go leaving something important out. Doh! Using Titegroup currently. I have some HP238 that I experimented with a while back, but it seemed smokier to me, maybe a little dirtier overall.


I had overlooked this section previously.

Reloading press used (list modifications if relevant)installed: Dillon 650, ceramic ball bearing/spring for smoother shell plate stops, ebay live primer chute catch can, and spent primer catch can
Caliber: 9mm
Bullet (Weight, Coating, Profile, Manufacturer): The Blue Bullets 125gr RN
Powder manufacturer, type and charge; volume, type (ball, stick, flake): Titegroup, was at 3.7-3.8gr, bumped up to 3.8-3.9gr just recently
Dies used: Dillon
Primers used: Winchester
Cartridge Overall Length (COAL): ~1.125
Chronograph data (if possible): chrono'd the 3.7-3.8gr load recently, and came out to a 132 power factor, with a standard deviation around 15fps for 10 rounds (so ~1060fps)
Goals intended with this load: This is my do everything load...I shoot it in matches, shoot it for practice/training, and use it in classes as well. While I could shoot "bunny farts" for competition and practice, I'd prefer the recoil impulse to feel not that extremely different from my carry ammo, which is currently 147gr HST or 124gr HST.
Results - accuracy, smokiness, clean burning, flash, temperature, smell, brass deformation, etc.: Seems accurate, at least as much as I can expect in my hands. A little smoky at times, can definitely smell it at times. Don't see any brass deformation.
Problems encountered and fixes applied: Early on when starting to load with Blue Bullets I did see some leading, but found it was 100% due to my own fault and crimping a touch too tight.
Anything of interest: Hope to chrono the 3.8-3.9gr soon, and will continue to run some more of it in practice to check for possible issues.